Brake Problems

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.

Drivers and technicians rarely make the connection between fuel economy and brakes. Moving the pads back from the rotor by only 1mm can increase fuel economy by as much as three to five percent. For engineers, it is a huge gain that does not involve exotic materials or adding expensive components.

Anti-Drag Systems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system. At the master cylinder on some vehicles, there might be a quick-take-up valve in the replenish port to hydraulically pull the caliper piston back from the rotor. At the caliper, OEMs are using seals with a special profile designed to retract the piston. Some vehicles are even using the valves in the ABS module to electronically retract the pistons. On the caliper bracket, engineers are designing hardware that can push the pad away from the rotor.

None of the drag-reducing technologies will work if the caliper is not moving freely. This is why replacing the brake hardware every time the pads are serviced is critical.

Hardware Wears Out

Like all springs, brake hardware can fatigue over time due to movement and lose spring tension. Another factor is heat. Every time the driver applies the brakes, the clip goes through a heat cycle. These cycles can add up over the life of the hardware and cause fatigue and the loss of spring tension.

The other type of wear is physical. As the pads move in the bracket, metal and surface coatings on the abutment clips can wear away. No matter how much anti-seize or brake lubricant is applied, the hardware will not be returned to new condition.

Anti-Drag Hardware

For more than two decades, automakers have been introducing new brake hardware components to help push the pads back into the caliper bracket. Most technicians may call them anti-rattle clips, but it is also a way to improve the fuel economy of the vehicle.

One of the best examples of anti-drag hardware can be found on some late-model GM vehicles. This abutment clip has a metal finger that pushes the pad away from the rotor. On the other side of the clip is a small tab that secures the pad in the bracket so it will not rattle.

Dodge uses a similar design on its full-sized trucks that has clips on to the ears of the pad. These clips can be difficult to install, but they can save the driver gas and your shop a noise comeback.

Anti-drag hardware can also reduce disc thickness variation (DTV) that can cause pulsation complaints. Most vehicles have a lateral runout specification of less than 0.002”. This wobble motion can cause the pads to come in contact with the rotor. The high spot of the rotor’s runout might hit the brake pads. This removes a very small amount of material from the rotor at the high spot of the runout, which can cause DTV. If enough material is removed over thousands of miles, it will cause brake pedal pulsation.

Aftermarket Improvements

Manufacturers of brake pads and hardware are making hardware that is better than what was installed by the OEM. Some hardware kits are using coatings on the abutment clips that keep the pad moving over the life of the brake job. They are also using rubberized coatings to insulate the pads to prevent brake noise.

There are also add-on clips that clip onto the pads to reduce drag. The clips apply pressure on each of the brake pads to keep them from contacting the rotor when not in use. The pressure is light enough that it does not affect the braking system when the brakes are applied.

You May Also Like

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.

The most challenging wheel bearing to replace is a cartridge or press-fit, otherwise known as a gen 1 wheel bearing. No matter what you call them, gen 1 wheel bearings can be found on domestic and import nameplate vehicles. Removing and installing these bearings requires the correct tools and patience. 

Tapered Wheel Bearings

Here’s what you should know as a technician when servicing tapered wheel bearings.

Understanding Passive Wheel Speed Sensor Operation

Passive types of wheel speed sensors are still used in many applications so understanding their operation is important.

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

How Regenerative Brakes Operate

Regenerative braking is a hybrid’s first choice for braking.

Other Posts

Steering Angle Sensor Service

Ninety percent of the time when a steering angle sensor code is active, it means the sensor needs to be calibrated.

Please Take Our Brakes/Rotating Electrical Survey

By entering, you’ll have a chance to win a $100 gift card or one of 10 $25 gift cards!

Replacing Master Cylinders

The most common problems that occur in the master cylinder are wear in the piston bore and piston seal failure.

Avoiding Brake Noise Comebacks

Brake systems are complex and require an understanding of the root cause of generating the noise.