Why Does My Car Shake When I Brake?

Why Does My Car Shake When I Brake?

Assuming that new pads and rotors will automatically fix the problem will only create more issues.

Judder is a vibration that can be felt in the seat or steering wheel, but it will not cause pulsing of the brake pedal. Judder can occur in a vehicle with zero runout or disc thickness variation (DTV), and is caused by brake torque variation (BTV).

BTV occurs when there is a variation of torque across the face of the rotor that causes the rotor to slip and catch as brake pads pinch the rotor. BTV may be caused by an inconsistent rotor finish, metallurgy or uneven deposits of friction material on the face of the rotor.

Assuming that new pads and rotors will automatically fix the problem will only create more issues with the customer when the vehicle inevitably comes back.

Knowing the difference between pulsation or DTV and judder/BTV is critical to solving any brake complaint and avoiding a problem in the first place. Assuming that new pads and rotors will automatically fix the problem will only create more issues with the customer when the vehicle inevitably comes back.

Rotor Finish and Transfer Layers

The friction between the two surfaces changes forward motion and braking force into heat, but there is a lot of science that goes into what happens at the molecular level to make that happen.

Most semi-metallic brake pads use the two different surface materials of the pad and rotor to make friction. The abrasive action wears away the two surfaces, but ceramic and some NAO pads transfer a thin layer of pad material onto the surface of the rotor. The transfer layer is bonded to the rotor’s surface and cannot be washed away by water or wheel cleaners. The only way to remove it is by using a brake lathe or abnormal heat. With this type of pad, it is critical to machine the rotor with the correct surface finish and follow the recommended break-in procedure so the transfer layer can be established.

Adherent friction is easier on rotors, but the pads become the primary wear component. The layer is always being worn and replenished by the brake pad during braking, so these pads produce dust. The smoothness of the friction surface of a rotor is described in terms of microfinish or RA factor. RA stands for “roughness average” and represents a way to measure the smoothness of a rotor. Most lathes on the market will yield very acceptable RA factors when they are in good condition and are used properly. The finish is essential to transfer material for organic and ceramic friction materials. The correct finish is also essential for semi-metallic pads so they can have the correct coefficient of friction during initial break-in.

You May Also Like

Adjusting Parking Brakes

You should never estimate when it comes to parking brake adjustments.

The parking or emergency brake has to perform two distinct jobs. First, it must be able to hold the vehicle on an incline. Second, it must be able to stop a vehicle under a specific distance if the hydraulic brakes have failed. These standards are set by the Department of Transportation (DOT), and the kicker is these standards must be met with the force applied by a little old lady. But, over time, the cables can stretch and the friction materials change their length and thickness, which is why adjustments to the system are required.

Charging More for Brake Jobs

Here’s why charging more for brake jobs keeps customers coming back.

Servicing Multi-Piston Brake Calipers

Caliper replacement may be necessary in high-mileage vehicles because of fluid leaks or because the calipers are sticking.

Wheel Bearings

Higher quality wheel bearings use higher quality steel that is properly heat treated.

EV Brake Jobs

With these vehicles, the major aggravation for shops is brake noise and uneven brake pad wear.

Other Posts

Brake Fluid 101: What Does Brake Fluid Do? What is the Difference Between DOT 3 vs. DOT 4?

When you think about the braking system of a vehicle, you probably think about the major parts you see when removing the wheel: brake pads, rotors, calipers and maybe hydraulics. However, one of the most important parts of the system isn’t visible: brake fluid. Brake fluid comes in several formulations for different applications and plays

Brake Pad Diagnostics

Worn brake pads can tell you a lot about the entire brake system and keep new components from suffering the same fate.

Understanding Passive Wheel Speed Sensor Operation

Passive types of wheel speed sensors are still used in many applications so understanding their operation is important.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.