Key Programming

Key Programming

You might think that key programming is a job for a locksmith or specialist, but the market is changing.

Three situations might require key programming capabilities at your shop. First, being able to diagnose and program keys can be a tool as part of some no-start diagnostics. Second, you may run into a situation where a key or fob needs to be reprogrammed to the vehicle if a module was replaced. Third, a customer might want an extra key, or all the original keys were lost.

You might think that key programming is a job for a locksmith or specialist, but the market is changing. Brick and mortar locksmith and dealership parts departments can cut key blanks, but it is up to you to make them work with the vehicle. In the case of some proximity keys, there is no key to cut – it is all up to you.

For most vehicles at your shop, it is not as much about programming a key to the car, but programming the car to the new key. Programming a vehicle to the key might require a procedure to put the vehicle into a learn mode; this is typically called “onboard” programming.

Newer vehicles require a scan tool to learn a new key or remote to perform onboard programming. You might already do this at your shop if you have the right scan tool and software.

Onboard procedures use the antenna coil on the vehicle to read the transponder or ID number in the new key or remote. The vehicle gets the key’s transponder to transmit, and the unique ID is learned by the vehicle during the procedure.  

PIN CODES

One of the changes made to some late-model vehicles is the requirement to have a three- or four-digit PIN code to perform onboard programming. This code resides in the module for the immobilizer system. 

You can contact the OEM for the code, or, in some cases, it might be found in the owner’s manual if you are lucky. But, some key programming tools can harvest the PIN code from the modules. VW and other makes require PIN codes, depending on specific model years.

PROGRAMMING KEYS

To increase security, some OEMs are requiring the key to transmit more than just the ID code. VW and other European manufacturers are requiring that the key transmits the unique VIN of the vehicle. Specialty key programming tools can program the transponder code and VIN onto a key.  

REFLASHING AND REPROGRAMMING

Data can go both ways when it comes to some key programming tools. Information from a key can be programmed into a module, or information from an existing model can be programmed onto a key. This tool function can save you if a module has been replaced or reflashed and the key information is lost. It is also helpful if you are in a situation where all the keys have been lost. 

For situations like this, you have several options. Some key programming tools and vehicles will allow you to clone key transponders in the memory of the vehicle. The key programming tool communicates with the vehicle to find the information about the existing keys, and then burns that code to a new transponder using a specialized attachment for the key. It may call for reflashing completely new transponder codes to a module. For some cars, this can be performed through a J2534 interface. Other cases may require the module or EEPROM chip to be removed for reprogramming.  Specialized key programming tools let you do it at your shop. 

The key and fob for modern vehicles are more than a key. They can start a vehicle remotely, open a rear hatch with a swipe of a foot, and make sure the vehicle is secure against physical and virtual attacks. If you are already servicing these vehicles, you can’t avoid key programming.

You May Also Like

Understanding ADAS: Blindspot Detection Systems

With the right tools and service information, it is possible to resolve a customer’s complaint. 

Blindspot detection was one of the earliest Advanced Driver Assistance Systems (ADAS) features offered on vehicles. The system alerts the driver to objects in the blind spot of the vehicle. Servicing these systems is straightforward to diagnose and repair.

Theory and Operation

Blindspot detection systems can use radar or cameras, and some systems use both. The radar sensors emit radiowaves that bounce off objects and are received by the sensor. The sensors are mounted in the rear bumper. Camera systems will have cameras mounted to the side mirrors or A-pillar. The image from the camera is processed by a computer to classify the object. Some systems will use both radar and camera sensors to make a more accurate classification.

For Better Customer Relations, Be A Better Listener

For a service advisor, asking questions and letting the customer explain can be a great diagnostic tool.

Electric Power Steering Diagnostics

Load management for steering systems.

Chassis Diagnostic Procedures

The secret is to be quiet & listen, as the customer will tell you almost everything relevant to the repair you need to know.

Turning Off The TPMS Light

If a vehicle comes into your shop with the TPMS light on, there are a few key things to check first for time’s sake.

Other Posts

ADAS Calibration Tips

Here are 10 tips to follow during ADAS Calibration.

ADAS and Vehicle Alignment

New vehicle ADAS and autonomous features all rely on the alignment being exactly as it should be.

TPMS Sensor Signals

TPMS sensor signals are low power and low frequency, with most sensors transmitting at 315MHz or 433MHz.

Hydraulic Control Units

The ABS module and HCU are the heart of any ABS or stability control system.