Thinking Through False ABS/ESC Activation Events

Thinking Through False ABS/ESC Activation Events

Electronic stability control (ESC) became a mandated safety feature for the 2012 model year. Along with all of these advancements, false activation complaints have surfaced. Solving them has been a diagnostic conundrum through the years. False activation incidents involve the ABS modulator taking over braking or intervening to restore vehicle stability. The customer may feel feedback in the brake pedal like a pulsation or sudden drop. Some may also experience a drop in power or the vehicle may suddenly pull in one direction.


Electronic stability control (ESC) became a mandated safety feature for the 2012 model year. Along with all of these advancements, false activation complaints have surfaced. Solving them has been a diagnostic conundrum through the years.

False activation incidents involve the ABS modulator taking over braking or intervening to restore vehicle stability. The customer may feel feedback in the brake pedal like a pulsation or sudden drop. Some may also experience a drop in power or the vehicle may suddenly pull in one direction.

WHEEL SPEED SENSOR PROBLEMS
The most common complaint on older vehicles is ABS activation at speeds between 3-15 mph. This problem usually starts with the wheel speed sensors. A weak signal from a sensor is interpreted as a locked wheel, which triggers the computer to activate the ABS system and release brake pressure in an attempt to unlock the wheel. The driver might experience a longer-than-normal stop.

On these older systems with passive sensors, the cure for false activation is to clean the tip of the wheel speed sensor, inspect the tone ring and adjust the air gap. This typically fixes the problem.

New magneto-resistive sensors or “active” wheel speed sensors are not prone to issues of metal accumulation on the tip of the sensor. But, debris can build up on the magnets embedded in the reluctor ring in the outer seal of some sensor. This can take a long time to accumulate.

False activations are still a problem with active systems, but more advanced modules are able to determine if a wheel is locked or if there is a wheel speed sensor problem. Instead of activating the ABS module and causing long stops, the system will deactivate and the ABS warning light will turn on.

ESC FALSE ACTIVATION PROBLEMS
The next false-activation scenario involves the ESC system. The source of the problem can be more than one sensor and can even be traced to alignment angles. The customer may not notice an issue until there is a mechanical problem with the brakes. In these cases, you may notice that one wheel is covered in brake dust. Some customers may complain the ESC activates on slower corners or on highway off ramps.

The most important sensor is the steering angle sensor (SAS), which measures steering angle, steering wheel speed and torque applied by the driver. This input tells the ESC system what the driver wants to do. The other sensors tell the ESC system what the vehicle is actually doing.

Let’s examine what happens during an understeer condition where the wheel turns, but the vehicle continues to travel in a straight line. The driver will continue to increase the steering angle, but the lack of traction keeps the vehicle going straight.

The ESC computer sees the understeer event via the sensors long before the driver realizes it. The ESC computer also sees that the driver’s steering angle is greater than the actual path measured by the yaw and lateral accelerometers.

The ESC system intervenes to try to make the vehicle turn. The first action might be to close the throttle to transfer weight to the front so the tires can gain traction. The next action might be to increase braking force on the inside front and/or outside rear tire to try to get the vehicle to rotate. All this time, the sensors are monitoring what the driver is doing and the effectiveness of the correction. This happens in nanoseconds.

Let’s say a steering position sensor is giving a false reading of an extra 50° when the car is traveling in a straight line. The ESC might perform a correction by activating the brakes in order to get the steering angle to match what the other sensors are seeing.

The other possibility is the extra 50° on an off ramp may trigger the ESC system because it is interpreting the signals as an understeer condition.

Another false activation scenario can be caused by an excessive thrust angle. The thrust angle is an imaginary line drawn perpendicular to the rear axle’s centerline. It compares the direction that the rear axle is aimed with the centerline of the vehicle. Excessive thrust angle can cause the vehicle to go down the road at an angle with the steering wheel turned to one side.

The ESC system can experience the effects of an excessive thrust angle, but it can’t see the thrust angle. The yaw sensor shows that the vehicle is not traveling in a straight line, and the accelerometers and the steering angle indicate that the driver might be trying to make a correction. The accelerometers tell the system that nothing is happening.

The ESC system might read this as the rear end starting to step out, which could be interpreted as an oversteer. The ESC system might try to correct the condition by pulsing the inside rear brake.

DIAGNOSTIC STRATEGIES
1. First, interview the customer and find out when and where the problem occurs. Ask a lot of questions.
2. Second, inspect the brakes for uneven wear. Compare the thickness of the pads on both sides of the axles. Also look for a single wheel covered in brake dust.
3. Third, with a scan tool, observe the sensor readings for the steering angle, accelerometers and yaw sensors. Calibration procedures with a scan tool can also solve many problems.

Lastly, information is key. TSBs and service information are vital to resolving certain problems. Since these systems operate on high-speed proprietary or CAN serial data buses, the integrity of the wiring harness is critical for operation.

You May Also Like

Adjusting Parking Brakes

You should never estimate when it comes to parking brake adjustments.

The parking or emergency brake has to perform two distinct jobs. First, it must be able to hold the vehicle on an incline. Second, it must be able to stop a vehicle under a specific distance if the hydraulic brakes have failed. These standards are set by the Department of Transportation (DOT), and the kicker is these standards must be met with the force applied by a little old lady. But, over time, the cables can stretch and the friction materials change their length and thickness, which is why adjustments to the system are required.

Charging More for Brake Jobs

Here’s why charging more for brake jobs keeps customers coming back.

Servicing Multi-Piston Brake Calipers

Caliper replacement may be necessary in high-mileage vehicles because of fluid leaks or because the calipers are sticking.

Wheel Bearings

Higher quality wheel bearings use higher quality steel that is properly heat treated.

EV Brake Jobs

With these vehicles, the major aggravation for shops is brake noise and uneven brake pad wear.

Other Posts

Advanced Wheel Bearing Diagnostics

Can a bump set a wheel speed sensor code?

Brake Fluid 101: What Does Brake Fluid Do? What is the Difference Between DOT 3 vs. DOT 4?

When you think about the braking system of a vehicle, you probably think about the major parts you see when removing the wheel: brake pads, rotors, calipers and maybe hydraulics. However, one of the most important parts of the system isn’t visible: brake fluid. Brake fluid comes in several formulations for different applications and plays

Understanding ADAS: Blindspot Detection Systems

With the right tools and service information, it is possible to resolve a customer’s complaint. 

Brake Pad Diagnostics

Worn brake pads can tell you a lot about the entire brake system and keep new components from suffering the same fate.