The Key To Stopping Brake Noise

The Key To Stopping Brake Noise

Noisy brakes are not squeaking door hinges waiting to be lubed. You cannot simply apply a magic substance to make them quiet. It is not that using lubricants, pastes and sprays are not effective, it is simply intuitive that minimizing friction (without consideration of braking performance) using the most expedient available application is cost effective with respect to service labor.

127999805090IMG_00000076807Once you understand the importance of this interface, you will understand the importance of brake rotor finish, pad selection and hardware. Brake systems are complex and require an understanding of what is the root cause in generating the noise. Noisy brakes are not squeaking door hinges waiting to be lubed. You cannot simply apply a magic substance to make them quiet. It is not that using lubricants, pastes and sprays are not effective, it is simply intuitive that minimizing friction (without consideration of braking performance) using the most expedient available application is cost effective with respect to service labor.

The key to stopping brake noise is to do the brake job right the first time. If a customer does come back due to noise, a shop must have a diagnostic process to resolve the problem the first time.

What is Noise?
805090DSCN0429j_00000036869As a set of brake pads clamp down on a rotor, they start to vibrate. As the pads, rotor and even the knuckle vibrate, they excite the air around them. The motion/vibration of the brake system pushes the air forward, compressing it, and when the fingers pull back, they suck the air back creating a low-pressure area. If you were to chart the pressure change over time, it would go up and down like a wave that would repeat itself (audible cyclic frequency) until the brake system stopped vibrating. These changes in the air pressure of a sound wave eventually enter your ear because the vibration and associated frequency also move at a constant speed through the air.This transmission and conversion of vibrations of sound waves into mechanical vibration and then into nerve impulses is one of the cornerstones for understanding NVH and brake noise.

All brakes make noise. When the friction material makes contact with the rotor, the coupling causes the brake pad and rotor to oscillate and vibrate. In engineering terms, this is called “force coupled excitation,” which means that the components are locked as a combined system that will vibrate at the system’s natural frequency combined modes of vibration.

The amount of excitation and the frequency generated can be influenced by variations in brake torque (or changes in the coefficient of friction) across the rotor’s face. As the components heat up, the rotor may develop hot spots that could cause the rotor to have different regions of friction that produce different levels of brake torque. This friction coupling is where most brake noise is generated.

Stopping Noise at the Start?
805090IMG0035jp_00000036870If you are trying to eliminate a noise, you could try to stop it from moving the air around it. To do this, you could eliminate the air or get further away from it. This is not possible with brakes because they do not operate in a vacuum and they cannot be separated from the vehicle. You can suppress or eliminate the path of vibration transfer from the source leading to noise through damping and isolation methods or dissipate the noise by insulation/absorption treatment. But the most effective method is to control the vibrations at the pad and rotor interface.

First, if a friction material is better at keeping a constant coefficient of friction across a broad temperature ranges and environmental conditions, it probably is a quiet pad. A “consistent” friction material causes less vibrational excitation variation at the friction coupling by having consistent brake torque at environmental extremes of humidity and temperature (-40F to 500F).

Second, some friction materials leave or transfer a layer of friction material (transfer film or “seasoning”) on the rotor’s surface that some friction material companies claim can smooth out the rotor surface, thereby causing less excitation and noise at the friction coupling. Also, this transfer layer may not be as sensitive to heat induced brake torque variation.

805090IMG1117jp_00000036871Poor rotor finish can lead to noise. When machining a rotor you have two primary goals — to provide a smooth surface finish for the pads and provide a true surface finish.

The smoothness of the friction surface of a rotor is described in terms of microfinish or RA factor. RA stands for Roughness Average and represents a way to measure the smoothness of a rotor. Most lathes out there, when in good condition and used properly, will yield very acceptable RA factors. The finish is essential to transfer material for organic and ceramic materials. Also, the correct finish is essential for semi-metallic pads so they can have the correct coefficient of friction during initial break-in.

Non-directional finishes can help in the bedding process and the establishment of a transfer layer. It can also prevent the grooves of the rotor from pulling and pushing on the pad like how a record moves a needle.

All brake pads must be bedded-in with the rotor they will be used against to maximize brake performance. The bedding-in process involves a gradual build up of heat in the rotors and pad compound. But, how this gradual heat and bedding process takes place is determined by the manufacturer of the pad.

Taking a vehicle for a test drive after a brake job lays down a thin layer of transfer film on to the rotor surface. Following the bed-in procedures provided by the manufacturer will assure a smooth, even layer of transfer film on the rotor and will minimize brake judders.

The break-in procedure is not to “cure” a pad and harden the resins. If a brake pad set produces an excessive amount of smell or smoke on the initial bedding procedure, chances are that there is something wrong with the pad and how it was manufactured.

There are not any set rules or universal procedure to bedding or breaking-in brake pads. Due to the fact that every manufacturer has different manufacturing processes, each has their own recommended procedure.

Some manufacturers recommend 400 to 500 miles of moderate driving with out hard stops, while some recommend 20 to 30 stops from a specific speeds. Most manufacturers are printing the break-in directions and dropping them in the box.

There are no miracle products that will stop all brake noise. It comes down to the basics of having a rotor with a high quality finish and friction material that is stable. Everything else is secondary.

You May Also Like

Adjusting Parking Brakes

You should never estimate when it comes to parking brake adjustments.

The parking or emergency brake has to perform two distinct jobs. First, it must be able to hold the vehicle on an incline. Second, it must be able to stop a vehicle under a specific distance if the hydraulic brakes have failed. These standards are set by the Department of Transportation (DOT), and the kicker is these standards must be met with the force applied by a little old lady. But, over time, the cables can stretch and the friction materials change their length and thickness, which is why adjustments to the system are required.

Charging More for Brake Jobs

Here’s why charging more for brake jobs keeps customers coming back.

Servicing Multi-Piston Brake Calipers

Caliper replacement may be necessary in high-mileage vehicles because of fluid leaks or because the calipers are sticking.

Wheel Bearings

Higher quality wheel bearings use higher quality steel that is properly heat treated.

EV Brake Jobs

With these vehicles, the major aggravation for shops is brake noise and uneven brake pad wear.

Other Posts

Brake Fluid 101: What Does Brake Fluid Do? What is the Difference Between DOT 3 vs. DOT 4?

When you think about the braking system of a vehicle, you probably think about the major parts you see when removing the wheel: brake pads, rotors, calipers and maybe hydraulics. However, one of the most important parts of the system isn’t visible: brake fluid. Brake fluid comes in several formulations for different applications and plays

Brake Pad Diagnostics

Worn brake pads can tell you a lot about the entire brake system and keep new components from suffering the same fate.

Understanding Passive Wheel Speed Sensor Operation

Passive types of wheel speed sensors are still used in many applications so understanding their operation is important.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.