SUV Wheel Alignment Basics

SUV Wheel Alignment Basics

Proper alignment of SUVs with larger tires help your customers to maximize their investments in these popular vehicles.

Wheel alignment is not only critical in maintaining a tire’s longevity, but it’s also an integral part of driving safety. As Americans gravitate to more SUVs with larger and more expensive tires, proper alignment is of increasing importance as a way for your customers to maximize their investment. 

Because wheel alignment is such an important part of tire service, shops should take a look at the tires and alignment anytime a vehicle is up on the lift for service. This will not only help you identify any problem areas, but it will also send the message to your customer that you’re monitoring the tires and undercar health of their vehicle. 

While a variety of alignment technology exists today, a technician will save time and get accurate alignment angle measurements with the quick-measure feature on an aligner. This feature helps spot alignment angle problems quickly so that technicians can correct them and drivers can be on their way. 

A good understanding of a vehicle’s alignment starts with the angles. Let’s do a quick review:

  • Thrust angle is the rear axle’s relationship to the centerline of the vehicle. Thrust angle that’s out of adjustment can cause a crooked steering wheel as well as a dog-tracking condition. On a solid rear-axle vehicle such as a truck, this can usually be seen as a bent frame. For vehicles with independent rear suspensions, an out-of-alignment thrust angle can be caused by toe settings being off in opposite directions.
  • Camber is the angle of the top of the tires when looking from the front. Camber can be adjusted at the top of the strut for front wheels or with a special kit for the rear wheels.
  • Caster is the tilt of the steering axis, either tilted forward (negative) or back (positive).
  • Toe is the angle most people are familiar with and is most visible to customers. It can be seen as the tires pointed inward (toe in) or outward (toe out) when viewed from the top.

When adjusting a vehicle’s alignment, technicians should always use a level alignment rack that is set on locks. The alignment rack should have the capacity to lift the vehicle that needs an alignment. about:blank

Technicians should also take their time when setting up the machine and pay attention to the proper alignment process such as setting tire pressure, unpinning turn plates and adjusting all angles in the correct order.

Service professionals should be thorough when conducting an initial test drive and inspecting the vehicle. A good shakedown of a vehicle to identify worn or damaged parts or tire wear can go a long way in ensuring the job is done right the first time.

Content provided by Coats Garage. For more information, visit coatsgarage.com.

You May Also Like

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Don’t miss a worn joint!

Detecting and measuring wear in a ball joint is critical to ensuring the safety of a vehicle. 

Types of Ball Joints

A ball joint is made up of a housing, ball stud, bearings, end cover and Belleville washer or spring. A Belleville washer is a conical-shaped spring designed to be loaded in the axial direction. The joint is attached to a control arm by pressing or riveting the joint into the arm. If the joint is pressed into the arm, it will require a special tool to remove the old joint and install the new one. 

Ride Height Sensors

If one of these sensors is replaced, it must be calibrated after it is installed.

GM Rattle or Creak Noise From Front Suspension

The noise may be originating from the front lower control arm front bushing. Here’s how to correct it.

Mercedes Airmatic Suspensions

Diagnostic tips to aid your repair efforts.

ADAS Sensor Corrections

When performing a calibration, you are adjusting the connection between the sensor, vehicle and surroundings.

Other Posts

Collision Blueprinting with Alignment Equipment (VIDEO)

An alignment is usually called for prior to ADAS calibrations. This video is sponsored by Hunter Engineering.

Rethinking Your Wheel Weight Assortment

Your wheel weights could be hiding indirect comeback costs related to them falling off or losing their adhesion.

Air Ride Conversion Kits

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring.

Curing Shock, Strut and Suspension Noise

As vehicles age, eliminating noise is Job 1. But ‘noise’ may mean different things to you and your customers.