Diagnostic Solutions: Hubs/Bearings, CV Shafts & U-Joints

Diagnostic Solutions: Hubs/Bearings, CV Shafts & U-Joints

Thanks to advanced technology, modern vehicles operate with fewer noise, vibration and harshness (NVH) complaints than ever before. Consequently, when a noise, vibration or harshness issue arises, it's most likely to be caused by worn drivetrain components like universal joints, constant velocity (CV) joints or wheel bearing hub assemblies. In any case, NVH complaints can often be the most challenging to diagnose when a tech or service writer can't duplicate the exact driving conditions under which they occur.

ght exist between their compression or extension lengths. Because using an impact wrench can damage the joint or adversely affect wheel bearing preload, always use a torque wrench to tighten the CV axle ­retaining nut to specification.

HUBS AND BEARINGS

Because tapered-roller front wheel bearings require frequent lubrication and adjustments, permanently preloaded and lubricated bearing hub assemblies have generally replaced them. Correct preloading is required in modern wheel bearing assemblies because the clearance between wheel speed sensors and tone rings is critical. Preloaded bearings also reduce the rotating friction of the disc brake assemblies by helping maintain a small, but significant, air gap between the brake rotor and pads.

since this wheel bearing had plenty of lubricant, it’s safe to assume that the failure was caused by a metallurgical problem.

When diagnosing any wheel bearing noise, it’s important to ­remember that modern wheel bearings must 1) support the vertical load created by the vehicle’s weight, 2) withstand the forward thrust of the driving wheels, and 3) resist lateral loading during cornering. Any noise coming from the wheel bearings will, therefore, be most often duplicated under one or more of these driving conditions.
See Photo 4.

 

When road-testing the vehicle to duplicate an NVH complaint, notice that wheel bearing and drivetrain noises are constant, whereas tire noises vary according to the road surface. If a ­vacant parking lot is available, weave the vehicle back and forth at low speed to alternately load and unload the wheel bearings. Notice also if the noise level changes as the vehicle stops and accelerates. After the wheel bearings have warmed up after an extended drive, check each bearing hub’s temperature with an infrared heat gun. In most cases, the defective wheel bearing will indicate a higher operating temperature.

Worn wheel bearings can cause clearance problems at the ABS sensor and store ABS trouble codes.

Last, raise the vehicle with the wheels suspended. Grasp each tire at the 12:00 and 6:00 o’clock positions to check for looseness caused by a loss of preload in the bearings. Looseness in the wheel bearings might also cause a wheel speed sensor trouble code to be stored in the vehicle’s ABS module. If the vehicle comes in with the ABS light illuminated and a wheel speed code stored, check that wheel for worn bearings.
See Photo 5.

When replacing bearing hub assemblies fitted into aluminum control arms, try heating the control arm with an electric paint removal gun. In most cases, the aluminum will expand enough to expedite removal of the hub assembly. Expedite installation by thoroughly cleaning and lubricating the hub’s mounting surfaces. Replace all retaining bolts as required, apply lubricant or threadlocking compound as directed and torque each to the manufacturer’s specification.  

You May Also Like

MEYLE Expands Electronics, Sensor Product Portfolio

The focus is on assistance systems and engine and transmission management, with more than 300 new part numbers.

Hamburg-based manufacturer MEYLE announced it is expanding its portfolio of electronic and sensor spare parts by more than 300 references "to meet the demand from independent repair shops for high-quality and precisely fitting parts." The focus is on assistance systems and engine and transmission management, with more than 300 new part numbers in the pipeline, as well as the expansion of its product range specifically for electric vehicles, the company said.

FCS Introduces 42 New Numbers in May

Complete strut assemblies, shock absorbers, shock absorber assembly kits and suspension struts for popular VIO applications are included.

Philips Ultinon Drive 5000 LED Lightbar Line Expands

Lumileds has expanded the Philips Ultinon Drive 5000 series to include eight models.

DMA Adds New BrakeMaster Coverage

New coverage for Ford and Chevy includes popular pickup trucks and SUVs.

Akebono Expands Severe Duty Disc Brake Pad Kits

Akebono said it expanded its severe-duty ultra-premium disc brake pad line by 14 new part numbers.

Other Posts
Tesla Model 3 TPMS Service

When replacing the tires on the Tesla, you will have to service the TPMS sensors.

Topology And Your Scan Tool

Topology influences how you access the modules with your scan tool.

Car properties detailed in "see proof" car image.
Axle Torque Procedures

Guessing the correct torque setting is a bad idea.

ShopOwner’s June Digital Magazine Available Now

This issue is free to download and read; priceless in business value.