Diagnostic Dilemmas: 8 Simple Rules ...

Diagnostic Dilemmas: 8 Simple Rules …

Many of the "Diagnostic Dilemmas" Gary Goms is called upon to solve aren't really all that complicated - but were caused by basic oversights and incorrect assumptions on the part of the technician. This situation has largely been caused by a lack of training and, in some cases, poor training.

Since I began doing part-time mobile diagnostic work for local shops, I’ve noticed that most “Diagnostic Dilemmas” I’m called upon to solve aren’t really all that complicated.

Most of these Diagnostic Dilemmas were caused by basic oversights and incorrect assumptions on the part of the technician. This situation has largely been caused by a lack of training and, in some cases, poor training.

For example, when on-board diagnostics were popularly introduced in the early 1980s, many early trainers had to fill voids in OEM information by gathering information from anecdotal sources. But, in hindsight, much of the information provided 20 years ago has been proven incorrect.

Unfortunately, the incorrect information and incorrect assumptions developed 30 years ago is still part of our diagnostic dialogue. In most cases, they fall into one of eight categories of common diagnostic mistakes.

photo 1: to solve for amps, cover the ampere portion with your finger and divide voltage by resistance. a circuit operating at 14.2 volts against a resistance of 2 ohms will, for example, carry 7.1 amperes of current.1. Skipping the Customer Interview
The most common mistake of service writers and technicians is assuming that any problem can be diagnosed by simply retrieving a trouble code. For that reason, many service writers fail to determine the actual customer complaint or gather the background information needed to quickly and efficiently address the problem.

To illustrate, last spring I was called to solve a cold-stalling problem on a 2005 Jeep Wrangler. The PCM had stored at least one throttle sensor-related DTC and, following a service bulletin on that particular failure, the shop had removed the driver’s air bag to test the cruise control circuits.

I won’t explore this issue since it became apparent that it wasn’t directly related to the stalling complaint. But it did momentarily divert my attention away from the immediate problem of the engine cold-stalling until it had warmed up for about one minute. After a short warm-up, the engine started and idled perfectly for the rest of the day. My first impression was a fuel quality problem, but I set that theory aside for the moment because fuel quality hasn’t been a problem in my community during the past eight years.

photo 2: assuming the resistance (ohms) remains the same, volts and amperes are inseparable components of any 
</p>
</p>
	</div><!-- .entry-content -->

		<div class=

You May Also Like

Driveshaft Diagnostics

The big challenge with late-model vehicles is the diversity of driveshafts. 

Some customers say they can’t live without four wheel drive (4WD) or all wheel drive (AWD) for the winter. What 4WD and AWD vehicles can live without is a driveshaft going to the rear wheels. Most late-model driveshafts are not serviceable and do not have any lubrication points. But, this does not mean that they can’t wear, or even fail.

Nissan CVT Clutch Point Relearn Procedure

The Adaptive Shift Control delivers responsive and powerful acceleration.

Diagnostic Test Drive For Drivetrain

A driveshaft center bearing can fail due to the bearing and the rubber isolator.

Constant-Velocity Axle Options

Whether new or remanufactured, complete CV axle assemblies can throw you a curveball from time to time.

10 Timing Belt Tips

Here are the some key installation and service tips to make your next timing belt job just a little easier.

Other Posts

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

Steering Angle Sensor Service

Ninety percent of the time when a steering angle sensor code is active, it means the sensor needs to be calibrated.

Replacing Master Cylinders

The most common problems that occur in the master cylinder are wear in the piston bore and piston seal failure.

MEYLE Expands Electronics, Sensor Product Portfolio

The focus is on assistance systems and engine and transmission management, with more than 300 new part numbers.