Tech Tip: ABS Service on Chevy Silverados

Tech Tip: ABS Service on Chevy Silverados

The customer complained that at speeds over 40-50 mph, the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time. The technician had already verified the condition and checked for codes before calling Identifix. He found code C0237 (rear wheel speed signal erratic) stored as a history code, but it had not ....

Vehicle: 1999 Silverado.

Customer Complaint: At speeds over 40-50 mph, the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time.

The technician had already verified the condition and checked for codes before calling Identifix. He found code C0237 (rear wheel speed signal erratic) stored as a history code, but it had not reappeared for him. Next he road-tested with a scanner, watching the vehicle speed input through the powertrain control module (PCM) and electronic brake control module (EBCM) data. When the ABS and brake light came back on, data was lost on the scanner for both the PCM and ABS. Something was crashing the class 2 data line — but what?

On this truck, the instrument panel cluster (IPC), body control module (BCM), EBCM, PCM and automatic transfer case control module (ATC) are all on the class 2 data line at pin 2 of the data link connector. The tech went to the splice pack (SP205) to determine which module was initially causing the problem. The splice pack joins all of the data circuits at one point, and is located on the lower left side of the dash behind the headlamp switch. The splice pack, a connector end with a jumper bar seated into it, is located on a short harness and often is taped to another harness. When the EBCM class 2 data wires were disconnected from the data line, the symptom was gone. Now we knew the EBCM circuit was causing the problem, so that left either a problem with the power/ground or the EBCM.

The tech checked the connector at the EBCM for corrosion and terminal condition — it was OK. Next he removed and cleaned the ground for the EBCM at the frame (see GM bulletin #04-05-25-002A). Using a headlamp to load the circuit, he load-tested the power and ground to the EBCM. The power and ground tested OK, but there was still a problem. A new EBCM fixed this one.

Written by IDENTIFIX GM Specialist Bill Siegmann. Bill is certified ASE Master and L1 with 20 years of diagnostic and repair experience.

For additional tech tips, visit www.identifix.com.

You May Also Like

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.

Drivers and technicians rarely make the connection between fuel economy and brakes. Moving the pads back from the rotor by only 1mm can increase fuel economy by as much as three to five percent. For engineers, it is a huge gain that does not involve exotic materials or adding expensive components.

Ball Joint Wear

As the wear increases, play increases inside the joint. 

Clarios Formalizes Joint Development Agreement with Altris

Altris will develop sodium ion cells for low-voltage tech while Clarios will lead in battery management systems, software, and system integration for battery design.

Driveshaft Diagnostics

The big challenge with late-model vehicles is the diversity of driveshafts. 

AMN Drivetime: Cal Ganda’s Continental Journey

Ganda embodies servitude leadership, prioritizing team success and customer-centricity.

Other Posts

Eli Opens Reservations for its Micro-EV in the US

The new Eli ZERO represents a new category of high-tech, efficient and sustainable micro-EVs, according to Eli Electric Vehicles.

Replacing Master Cylinders

The most common problems that occur in the master cylinder are wear in the piston bore and piston seal failure.

MEYLE Expands Electronics, Sensor Product Portfolio

The focus is on assistance systems and engine and transmission management, with more than 300 new part numbers.

FCS Introduces 42 New Numbers in May

Complete strut assemblies, shock absorbers, shock absorber assembly kits and suspension struts for popular VIO applications are included.