Tech Tip: Silverado Owner Complains that ABS Light Comes on at 40-50 mph

Tech Tip: Silverado Owner Complains that ABS Light Comes on at 40-50 mph

At speeds over 40-50 mph, the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time. The technician had already verified the condition and checked for codes before calling Identifix. He found code C0237 (rear wheel speed signal erratic) stored as a history code, but it had not reappeared for him. Next he road-tested with a scanner, watching the vehicle speed input through the powertrain control module (PCM) and electronic brake control module (EBCM) data. When the ....

Vehicle: 1999 Silverado.

Customer Complaint: At speeds over 40-50 mph, the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time.

The technician had already verified the condition and checked for codes before calling Identifix. He found code C0237 (rear wheel speed signal erratic) stored as a history code, but it had not reappeared for him. Next he road-tested with a scanner, watching the vehicle speed input through the powertrain control module (PCM) and electronic brake control module (EBCM) data. When the ABS and brake light came back on, data was lost on the scanner for both the PCM and ABS. Something was crashing the class 2 data line — but what?

On this truck, the instrument panel cluster (IPC), body control module (BCM), EBCM, PCM and automatic transfer case control module (ATC) are all on the class 2 data line at pin 2 of the data link connector. The tech went to the splice pack (SP205) to determine which module was initially causing the problem. The splice pack joins all of the data circuits at one point, and is located on the lower left side of the dash behind the headlamp switch. The splice pack, a connector end with a jumper bar seated into it, is located on a short harness and often is taped to another harness. When the EBCM class 2 data wires were disconnected from the data line, the symptom was gone. Now we knew the EBCM circuit was causing the problem, so that left either a problem with the power/ground or the EBCM.

The tech checked the connector at the EBCM for corrosion and terminal condition — it was OK. Next he removed and cleaned the ground for the EBCM at the frame (see GM bulletin #04-05-25-002A). Using a headlamp to load the circuit, he load-tested the power and ground to the EBCM. The power and ground tested OK, but there was still a problem. A new EBCM fixed this one.

Written by IDENTIFIX GM Specialist Bill Siegmann. Bill is certified ASE Master and L1 with 20 years of diagnostic and repair experience.

For additional tech tips, visit www.identifix.com.

You May Also Like

How Regenerative Brakes Operate

Regenerative braking is a hybrid’s first choice for braking.

A hybrid vehicle is a different animal than many of us are used to seeing. After all, if the engine of a typical vehicle stalled out at a traffic light, the driver of that vehicle would know something was wrong with it. If that same vehicle still drove with the engine off, then that would mean they were probably going down hill. But, in the hybrid world, that is all normal. Systems around the vehicle are impacted by two key features:

Tesla Wheel Bearing Replacement

The process of replacing the hub unit on a Tesla is the same as many cars and light trucks.

Brake Pad Edge Codes – What Can They Tell You?

The edge code is a language written by engineers, federal entities and industry associations.

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.

The Real Cost of Installing Cheap Brake Pads

The brake repair market is starting to become dominated by a “good enough” mentality.

Other Posts

ADAS False Activation Evolution

The logic behind most ADAS warnings or corrections is to examine the plausibility of the situation.

Understanding ADAS: Blindspot Detection Systems

With the right tools and service information, it is possible to resolve a customer’s complaint. 

Brake Boosters and Start/Stop Vehicles

For a vacuum brake booster to work, it needs a source of vacuum.

Wheel Speed Sensor and Hub Unit Diagnostics

All wheel speed sensor codes are just the starting points of a diagnosis and not a reason to order a part.