ZF Tech Tip: Recognizing Chassis, Steering Systems Damage Patterns

Recognizing Steering System And Chassis Damage Patterns

If these components are damaged, the person steering needs to expect the handling of their vehicle to become critical.

CHECK RUBBER BELLOWS, BOOTS AND CLAMPING RINGS

Careless driving and dirt accumulation significantly increase the risk of wear on safety-relevant chassis and steering components. Technicians need to pay attention to typical damage patterns and remedy defects as required. If chassis or steering components are damaged, the person steering needs to expect the handling of their vehicle to become critical. Experts at ZF Aftermarket therefore advise workshops to inform their customers of how important a regular inspection is. Many components can be affected.

Technicians should particularly check whether the rubber bellows on the joints are worn, damaged or leaking. Because any splash water that gets in washes out the special grease, this then allows dirt particles to enter the joint. These particles destroy the inner plastic spherical shell and damage both the ball stud and the joint housing. This means that the clearance in the joint no longer meets the standard. Within the steering, the tie rod requires special attention: Apart from the rubber bellows, the steering boot needs to be checked for damage. The spring clamping rings should also be looked at so that any spots of rust are already identified as soon as they appear.

CURB CONTACT WITH CONSEQUENCES

On the chassis, the supporting joint, control arms and the stabilizer can show serious damage caused by corrosion, invaded foreign objects or dirt accumulation. In addition, driving over curbs is often the cause of defects. The consequences of damage greatly impair the vehicle handling and thus, the driver’s safety. Apart from that, they often lead to increased wear on other chassis components as well as to tires wearing unevenly and worse riding comfort. This means higher risk of accidents and additional repair expenses.

REGULAR VEHICLE INSPECTION

ZF Aftermarket recommends special tools for professional and smooth inspection or removal of supporting joints. This minimizes the risk of injury and reduces repair costs. ZF Aftermarket feels obliged to draw attention to the need for regular vehicle inspections: After all, the idea is to improve safety on the roads.

Courtesy of ZF

You May Also Like

Buick Encore Alignment Service

Alignments are key to the health of the tires and some of the advanced safety systems like automatic emergency braking and lane keeping.

The 2012-2022 Buick Encore is based on the Gamma II platform that is shared with the Chevy Trax. This has been the best-selling Buick for several years. Like a lot of modern vehicles, the alignment specs are tight with almost no adjustments built in except for toe. However, alignments are key to the health of the tires and some of the advanced safety systems like automatic emergency braking and lane keeping.
Front Suspension
The front suspension on the Encore has a single lower control arm and MacPherson struts. Some models have a suspension dampener on the front bolt of the lower control arm. The part helps to control vibration that could be transmitted to the subframe. If the caster is out of specification, look at the bushings on the lower control arm for damage. Camber can be adjusted by installing cam bolts in the lower hole of the strut mount. This should give ±1.75 degrees of adjustability. Inspection of the lower control arm is a critical part of aligning the Encore. The arm can be bent due to curb strikes and the bushings can quickly deteriorate. Also, inspect the sway bar links for any signs the ends have play.
Rear Suspension
The Encore comes in front-wheel-drive and all-wheel-drive versions. Both versions use a trailing arm beam axle. The camber and toe for the front-wheel-drive version can be adjusted with shims. Unfortunately, there are no adjustments for the all-wheel-drive version. If camber or toe are out of specification in the rear, look for a damaged wheel. If the thrust angle is out of specifications, inspect the trailing arm bushings.

Live Axle Wheel Bearing Service

Replacing rear wheel bearings on a live axle rear suspension requires a few extra steps when compared to a unitized bearing.

Ride Height Sensors

If one of these sensors is replaced, it must be calibrated after it is installed.

Ride Control For Electric Vehicles

Replacement units are available from sources other than the dealer.

Brake Pad Edge Codes

The “Edge Code” can tell you information about a brake pad’s friction material.

Other Posts

We Want Your Thoughts On Electronic Power Steering

Your opinion matters us and can be profitable for you too! Share your ideas with us.

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

Mercedes 4MATIC Diagnostics

The Mercedes-Benz 4MATIC all-wheel drive (AWD) systems have been around for a while now.

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.