Tech Tip: Volvo Brake Goes Too Low on First Application

Main Navigation

Advertisement
Social Connect
Resources
Our Brand Family
Brake and Front End Magazine
Technical Resources for diagnosing and servicing undercar components
Wheel End

Tech Tip: Volvo Brake Goes Too Low on First Application

If a customer complains of Volvo brakes going too low on first application, it may be because of improperly installed brakes or aerated fluid.

Brake and Front End Staff
By Brake and Front End Staff
Published:

Vehicle Applications:

Related Articles

1999 S80 2.9L, Vin 97, Eng Des B6304S, USA/Canada
2000 S80 2.8L, Turbo, Eng Des B6284T, USA/Canada
2001 S60 2.4L, Turbo, Eng Des B5244T3, USA/Canada
2002 S60 2.4L, Turbo, Eng Des B5244T3, USA/Canada
2002 S80 2.9L, Vin 91, Turbo, Eng Des B6294T, USA/Canada
2003 V70 2.4L, Turbo, Eng Des B5244T3

 

Customer Concern: On first application the brake goes low, almost to the floor; after that the brake is OK.

Potential Causes: Improperly installed brakes; ­aerated fluid.

 

Tests/Procedures:

1. Check brake clips for proper installation. A mis-­installed clip will cause this problem. The bottom of the clip should go around the bottom of the caliper bracket.

2. Check for any air in the hydraulic system. Try bleeding with a pressure bleeder.

3. Bleed at the ABS hydraulic unit lines. Sometimes air can get trapped in this area, which is under the master cylinder.

Courtesy of Identifix, Inc.

You May Also Like

EV Bizz

How Regenerative Brakes Operate

Regenerative braking is a hybrid’s first choice for braking.

Andrew Markel
By Andrew Markel
Andrew Markel is the director of content for Brake & Front End magazine. He has been with Babcox Media for 20 years. He is a technician and former service writer and holds several automotive certifications from ASE and ­aftermarket manufacturers. He can be reached at [email protected].
Published:

A hybrid vehicle is a different animal than many of us are used to seeing. After all, if the engine of a typical vehicle stalled out at a traffic light, the driver of that vehicle would know something was wrong with it. If that same vehicle still drove with the engine off, then that would mean they were probably going down hill. But, in the hybrid world, that is all normal. Systems around the vehicle are impacted by two key features:

Read Full Article

More Wheel End Posts
Tesla Wheel Bearing Replacement

The process of replacing the hub unit on a Tesla is the same as many cars and light trucks.

By Andrew Markel
Brake Pad Edge Codes – What Can They Tell You?

The edge code is a language written by engineers, federal entities and industry associations.

By Andrew Markel
Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.

By Andrew Markel
The Real Cost of Installing Cheap Brake Pads

The brake repair market is starting to become dominated by a “good enough” mentality.

By Andrew Markel

Other Posts

ADAS False Activation Evolution

The logic behind most ADAS warnings or corrections is to examine the plausibility of the situation.

By Andrew Markel
Understanding ADAS: Blindspot Detection Systems

With the right tools and service information, it is possible to resolve a customer’s complaint. 

By Andrew Markel
Benefits of Using Brake Parts Designed to Work Together

When replacing brake system components, it might seem like using compatible parts from any manufacturer – regardless of brand – should get the job done. However, for the safest brake job with the best performance, it’s always best to use parts from the same manufacturer, like ADVICS, where our brake pads, brake rotors, hydraulics, calipers

By Advics
Brake Boosters and Start/Stop Vehicles

For a vacuum brake booster to work, it needs a source of vacuum.

By Andrew Markel