Best Tech Advice: Replace Pads AND Rotors

Best Tech Advice: Replace Pads AND Rotors

Replace the rotors AND the pads during the same service. Sponsored by The Group Training Academy.


When you replace the brakes on your customers’ vehicles, you can explain how important it is to fix both sides at the same time. But even if the rotors appear to be okay, did you know it’s in everyone’s interest to replace the rotors AND the pads during the same service?

The fact is, brake pads and rotors work together to maximize braking performance. When fresh pads are installed and the burnish or break-in procedure is completed, a very thin layer of friction material from the pads is imprinted onto the face of the rotor. This continues to happen during normal driving. If you simply “pad slap,” or put new pads on old rotors, the surface is worn out and a strong transfer layer cannot be created.

New pads almost always require a fresh rotor surface so the pads can deposit a thin layer of friction material to increase braking performance. If old deposits of the previous material are on the rotor, it can contaminate the new pad and lead to performance and noise issues.

All brake pads use two different types of friction to stop vehicles – Abrasive and Adherent friction. 

Abrasive friction is pretty simple; it works similar to sandpaper. The brake pads press against the rotors and cause friction to help slow the vehicle.

Adherent friction is more complex, but can be visualized with a piece of duct tape. If you stick tape to a wall, it will probably stick just fine, but it will peel off relatively easily. But if you stick the adhesive to itself, you’ll have a much more aggressive bond.

With adherent friction, the pad is adhering to the thin layer of pad material on the rotor. The making and breaking of those many small bonds causes adhesive friction and helps slow the vehicle.

Semi-Metallic pads tend to use more abrasive friction and less adherent friction, while ceramic pads tend to use more adherent friction and less abrasive friction. In all pads, though, both abrasive and adhesive friction are at work at all temperatures, but in general terms, abrasive friction occurs mainly when cold and adherent friction “wakes up” when the brakes are warm/hot.

Whichever friction formulation is right for your customer, be sure to install the pads correctly. We’ve heard of more than one professional who installed the brake pads backwards.

Here are some other tips for quality, come-back free brake jobs.

Remember, the brake system works harder than any other safety system on your customers’ vehicles. Each time they stop for a light or slow down in traffic, their brakes ensure that they can do so safely. Because of this alone, it is always a good idea to use new parts for all your brake service.

Caliper guide pins on floating calipers are often overlooked – clean them in solvent and apply new grease. It is under extreme heat and pressure so always use a caliper specific grease. And NEVER put a torn boot back on a car.

Remember a first-class brake repair comes down to quality components and quality procedures. For more tips, visit

This video is sponsored by The Group Training Academy.

You May Also Like

Headlight Options

Many of your customers may be installing LED upgrades in their vehicles. Sponsored by The Group Training Academy.

Lighting options in today’s cars are more varied than they’ve ever been. For many reasons, traditional replaceable halogen bulbs are not the only things you may face in the service bay.

According to Philips, headlight bulbs begin to project significantly less light within two to three years of their initial usage, producing dimmer light outputs that compromise the safety of drivers and their passengers.

Headlights and Visibility

Headlights are continually evolving to keep up with safety and styling. Sponsored by The Group Training Academy.

Headlight Bulb Replacement

Don’t overlook the role lighting plays in keeping drivers and passengers safe. Sponsored by The Group Training Academy.

It’s Time to Nominate The 2023 School of the Year!

The School of the Year competition is a national contest that finds and names the best technician training school.

Performance Revolution CV Axles

Are you disappointed with the relatively short lifespan of many aftermarket CV boots? Sponsored by GSP Automotive Group.

Other Posts

Drilled and Slotted Rotors

There’s real science behind the location of holes, slots and grooves in today’s brake rotors. Plus, they look great too.

Charging More for Brake Jobs

Here’s why charging more for brake jobs keeps customers coming back.

Brake Pads – Customer Questions

Consumers have questions about brake pads. They ask us, so we figure we’ll share them so you can be prepared.

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.