Tech Tip: What Really Wears Out Inside Shocks and Struts

Main Navigation

Advertisement
Social Connect
Resources
Our Brand Family
Brake and Front End Magazine
Technical Resources for diagnosing and servicing undercar components
Chassis

Tech Tip: What Really Wears Out Inside Shocks and Struts

When shocks and struts wear out there are almost no visual clues. When a unit is leaking, it is a sign of failure and not wear. Next to performing an autopsy or throwing the unit on a dynamometer, there is no conclusive way to determine if the internal components are worn to a point where it could compromise vehicle stability. Even the "knee on the bumper" test can give false results due to how some units handle low frequency movements.

Andrew Markel
By Andrew Markel
Andrew Markel is the director of content for Brake & Front End magazine. He has been with Babcox Media for 20 years. He is a technician and former service writer and holds several automotive certifications from ASE and ­aftermarket manufacturers. He can be reached at [email protected].
Published:

3_01_2009/86804PistonSeal_00000041859.jpg” border=”0″ ” align=”right” alt=”one area of wear is the seal between the piston and bore. the seal must prevent fluid from flowing between the two surfaces without creating excessive amounts of friction. if the seal allows to much fluid to pass, it will influence how the valves in the piston and base perform. if the fluid becomes contaminated, it can cause wear to the bore and piston. according to some shock and strut suppliers, wear on these surfaces does not happen until the unit has become significantly degraded. “/>when a stone hits the chrome shaft of a shock or strut, it will first cause a pit or scratch. this might cause damage to the seal, which might cause a loss of fluid. if the the damaged area starts to corrode, it could cause the shaft to lose even more chrome. the seal at the top of the body is the barrier between the harsh environment outside and the fluid and gas within the unit. the seal can not be effective if the surface of the shaft is pitted or damaged. poor sealing surfaces can cause the unit to leak. if the pitting or lost chrome plating is large enough, it can damage the seal, this can lead to water and debris getting into the unit and damaging the valves and piston seal. to protect the seal, it is essential to replace the boots, dust covers and jounce bumpers. if any of these items are missing, it could cause the premature failure of the new unit. Here is where most of the wear occurs in a shock or strut. These small discs of metal are mounted on the shaft and are held in place with either a nut or a nut and spring. As the piston moves, the discs deflect and fluid moves between the two chambers. Even under normal conditions on a smooth road, shocks stroke on average 1,750 times for every mile traveled. The action causes a “shearing” action on the fluid that is not unlike what motor oil is subjected to when it is between engine bearings. This action can break down the base oil and additive package. The wear on the fluid can change the viscosity of the fluid and make the unit unable to dampen suspension movement. The discs and springs in the valves can also suffer from metal fatigue due to the constant movement of the suspension and the passing of the fluid.

Related Articles

You May Also Like

News

Continental Tire Opens Retread Solutions Center in South Carolina

The company said it hopes to uncover new improvements and technologies to innovate the retread process.

Brake and Front End Staff
By Brake and Front End Staff
Published:

Continental Tire recently opened its Continental Retread Solutions Development Center in Rock Hill, S.C., with a focus on retread process improvements and technology development. The goal, Continental says, is to bring “innovation and up-to-date retread processes to Continental’s Retread Solutions Partners and the fleets they serve.”

Read Full Article

More Chassis Posts
High-End Ride Control Rehab

Electronically adjustable shocks and struts use conventional mono-tube and twin-tube oil-filled dampeners.

By Andrew Markel
Toe Angles and Tie Rods

It is critical to remember that toe is not always zero or straight ahead.

By Andrew Markel
ADAS Module Programming

Reflashing and reprogramming is a necessary service for repairing vehicles.

By Andrew Markel
Live Axle Wheel Bearing Service

Replacing rear wheel bearings on a live axle rear suspension requires a few extra steps when compared to a unitized bearing.

By Andrew Markel

Other Posts

Sun Auto Tire & Service Expands Texas Store Count

The company has acquired Carrollton Complete Automotive, which offers a range of automotive services.

By Brake and Front End Staff
Philips Announces GoPure GP5212 Automotive Air Purifier

It uses a 3-layer filter to deliver cleaner, healthier, fresher air on the go, Lumileds said.

By Brake and Front End Staff
AACF Launches 65th Anniversary Fundraising Initiative

The campaign aims to raise $65,000 through 1,000 donations of $65 each.

By Brake and Front End Staff
Standard Motor Products Announces 123 New Numbers

The release provides new coverage in 53 distinct product categories and 47 part numbers for 2023 and 2024 model-year vehicles.

By Brake and Front End Staff