YouTube And TV: Talent And Presentation

YouTube And TV: Talent And Presentation

Some videos are nothing more than a shade tree mechanic screaming at the camera about expensive parts in quick two-second cuts before doing a burnout. Some videos have slick graphics and catchy intro music. You never know what you are going to get until you click on the video.

Andrew MarkelIn the mid-1990s, I would sit down in front of the TV on Saturday mornings with my father, and we would watch a block of shows on SpeedVision about car repair.

Most of the shows put actors in front of the camera with scripts. You could tell some of the “talent” had no experience turning a wrench for a living. Their job was to look good and not screw up the lines. As car nuts, we would yell at the TV whenever they did something stupid, which was often.

These pitchmen were often used for in-show commercial breaks, and you always knew when the guy in front of the camera was trying to sell you something. Fast forward to today, and the line between commercial and content is even blurrier on YouTube.

YouTube

I’ve been watching a lot of YouTube repair videos this month to avoid political news and ads. Some evenings, I “fall down the rabbit hole” and find myself watching for hours.

Some videos are nothing more than a shade tree mechanic screaming at the camera about expensive parts in quick two-second cuts before doing a burnout. Some videos have slick graphics and catchy intro music. You never know what you are going to get until you click on the video.

The content in some of these videos is good. Some videos are 40 minutes of a technician replacing a ball joint, while another video on the same topic may be only two or three minutes. Both videos get you to the same destination, but one takes the scenic route. Some of my favorite channels are nothing more than a technician with a GoPro camera strapped to his head.

The Game

A lot of these YouTubers have large audiences. Some channels have almost a million subscribers, and a video could get 250,000 views in less than a week. 

If the YouTuber decides to monetize their channel, ads will appear. It could be a 15-second ad at the start of the video, or it could be a banner. YouTube shares the ad revenue with the author of the video. It is estimated that creators receive $1 per 1,000 views, but this number can vary. Posting these videos can be very lucrative, and a select few have quit their day jobs to focus on producing them.

The Dark Side

A number of these guys are getting attention from tool and parts companies. Some companies shower these video stars with free tools and even offer them parts for their project vehicles. While I’m a big fan of these videos for the most part, some disclosure rules need to be put in place and enforced by YouTube.

It is not uncommon for an oil company, for instance, to invite some of these YouTube personalities to go on a trip to a racetrack, air show or R&D facility. The week after the trip, a lot of the channels will have similar videos. Some guys will clearly state in the video or in the description who paid for the trip, but most will never explain any potential conflicts of interest.

I don’t know what the financial arrangements are for these videos, but it is clear that the company is throwing some nice travel perks at these guys, sometimes even including corporate jet usage. I just wonder if they are also slipping some spending money into their pockets on these trips as well.

The good news is that if a video steps over the line, there is a “dislike” button and a comments section. Now where were these tools back in the day when I was watching SpeedVision with my father?

You May Also Like

Toe Angles and Ride Height 

Zero toe angle is present when both tires are parallel to the center thrustline.

How can a mysterious case of tire wear occur in a perfectly aligned vehicle? It happens and the answers aren’t always simple. To better explain, let’s go back a few decades when I aligned a 1983 Mitsubishi RWD pickup, only to have it return a month later with a tire scuffing complaint. Although the outside edge of the right front tire showed evidence of toe-related wear, the current toe angle was 0.100 inches, which is within the Mitsubishi’s +0.080” to +0.350“ specification.

Sona Comstar Inaugurates Manufacturing Plant in Mexico

The new facility will specialize in producing differential assemblies and reduction gears meticulously designed for BEVs.

Axle Torque Procedures

Guessing the correct torque setting is a bad idea.

What Constitutes A Quality Wheel Hub Assembly?

Discover key factors to consider for quality hub assemblies and how they impact vehicle performance and longevity.

Needs Come First When Choosing Aftermarket Or OE

It’s essential to understand the differing needs of manufacturers, shops, technicians, and consumers.

Other Posts

Service Opportunities Still Exist With EVs

Like all ICE vehicles, you need the correct tools, parts and to follow the proper service procedures when servicing EVs. This video is sponsored by The Group Training Academy.

Do Technicians Need Tips?

Asking for a tip would not go over well with your future customers.

Wheel Bearing Shortcuts

When you’re installing a wheel speed sensor on a hub unit, never ever remove it from the original unit. Sponsored by Auto Value and Bumper to Bumper.

Green Li-ion Launches Lithium-Ion Battery Materials Plant

The plant is North America’s first commercial-scale plant to produce recycled lithium-ion engineered battery materials.