What To Inspect Before Replacing The Serpentine Belt (VIDEO)

What To Inspect Before Replacing The Serpentine Belt (VIDEO)

Friction between the belt and pulleys wears away at the belt. This video is sponsored by the Group Training Academy.

Visual inspection of a vehicle’s serpentine belt is more critical than ever – but advanced belt construction features mean the process has changed. No longer can you simply spot the old cracks and fraying that indicated a potential imminent failure. You need to know what to look for and equally as important, how to do it properly.

The serpentine belt is part of a system and is not the only component susceptible to wear. The tensioner, idlers and pulleys all have the same design life as the belt. On some vehicles (if equipped), the decoupler pulley on the alternator wears over time and needs to be inspected and replaced when needed.

Friction between the belt and pulleys wears away at the belt.  This wear usually occurs on the sidewalls of the ribs. This material loss on the ribs allows the belt to slip in the drive. The belt can no longer efficiently drive the accessories which affects their performance.

In addition to checking the grooves, watch the belt while the engine is running. If you see a lot of movement or flutter in the belt, the tensioner is probably weak or sticking and should be replaced. The drive should be checked for any misalignment in the pulleys. This can sometimes be done visually (with the engine off) but usually requires the use of more sophisticated tools like a laser alignment tool.

Replacement serpentine belts must be the same length as the original. Make sure the belt that is being installed is applicated for the vehicle it is being installed in. Low-quality replacement belts may not be the correct length and will push the tolerances of the tensioner. A belt that is too short, for example, will cause too much tension and put higher than normal loads on the bearings inside the alternator, power steering pump and water pump. A belt that is too long may slip, make noise and wear prematurely. It will also cause the tensioner to work harder and fail sooner.

OAD decoupler pulleys that are installed on higher amperage alternators enhance engine efficiency andenable the alternator to “coast” freely in cases of sudden belt deceleration. If the pulley fails, it will cause noise and belt flutter, which may also affect the automatic belt tensioner.

To most accurately inspect the alignment in the pulley system, use a laser alignment tool. By doing so, you can uncover if you have one or more belt-eating culprits such as parallel or angular misalignment. Pulley run-out is misalignment from a bent component shaft or worn bearings. During your inspection, keep an eye out for bent or broken accessory brackets, and look for loose, missing or broken bolts – these items will contribute to belt alignment issues.

You can also check the system without the belt in place. With the engine off, try to move the pulleys fore and aft to make sure the mounting is tight, and the pulley exhibits minimal axial movement, which can cause misalignment. With your hands, move all idlers fore and aft and check for free rock. Excessive movement indicates a bearing or alignment problem, and that the idler should be replaced. Make sure that any misalignment issues are taken care of.

Many systems with excess misalignment can be corrected by accessory mount shimming, shifting the position of the pulley on the accessory shaft or loosening the accessory mount points and varying the sequence of tightening.

With the engine off and the belt removed, the tensioner can be inspected more closely. Rotate the tensioner pulley by hand and feel for bearing roughness. A rough bearing indicates the potential for immediate failure and that the tensioner should be replaced. While rotating the pulley, look for (and remove) any accumulation of foreign material on the pulley surface.

With the proper tool, move the tensioner arm as if you were installing a new belt; move the arm through the full range of available travel. By feel, you can detect if there is roughness or sticking of the tensioner arm during this movement. Replace the tensioner if sticking is detected.

As a final step, attempt to move the tensioner arm toward and away from the engine. If looseness is detected, the pivot bushing in the tensioner has worn excessively and the tensioner should be replaced.

Remember, If you are replacing just the belt without looking at the other components, you could be sending a new belt to a premature death.

This video is sponsored by The Group Training Academy.

You May Also Like

EV Safety Basics on the Shop Floor – Part II

As long as you follow the EV guidelines, you are going to have to use the proper PPE and insulated tools.

Staying safe while working on an electric vehicle requires the correct shop equipment as well as the correct personal protective equipment (PPE) and shortcuts are simply not an option. Let’s take a look at everything you are going to need.

We’ll start with PPE and electrical safety gloves. Class zero electrical insulating gloves rated for 1000 volts are required for EV service. Simply put, these gloves prevent high voltage from traveling through your hands, and they must be tested every time you use them by checking for a pinhole or any damage that could allow voltage to pass through a glove. A glove inflator is the most efficient way to do this. Insulating gloves must also be clean and dry so there are no conductive substances that can allow high voltage to travel outside the glove to your arm. Treat these safety gloves with extreme care. They can be damaged easily and they’re sensitive to UV rays, so they should be stored in a dark, dry environment. A ventilated UV-resistant bag is the best option. Safety gloves must also be re-certified every six months. You’ll also wear them with a leather outer glove to protect them, most prefer to wear an inner cotton glove as a liner to allow your hands to breathe.

EV Safety Basics on the Shop Floor – Part I

It’s critical to utilize OEM service information and procedures for each and every hybrid or EV.

Autel MaxiSYS Ultra Enhances Efficiency At Mighty Auto Pro

Time is money in vehicle repair, and the Autel MaxiSYS Ultra is all about enhancing technicians’ diagnostic prowess.

Empowering the Automotive Aftermarket Through Collaboration

Distributors, manufacturers, training institutions, associations and service providers all help automotive professionals stay ahead in a market that is constantly evolving with new technologies, trends and customer demands.

Understanding LSPI & Engine Oil

Using the correct manufacturer-recommended oil is crucial for peak performance and long-lasting engine health.

Other Posts
Randy Breaux, Group President, GPC North America, Talks to AMN Drivetime

At NAPA, “Breaux Knows” business relationships, ABCs to avoid, and serving the automotive professional.

Serpentine Belt and Drive System Maintenance

Properly maintaining the entire drive system prevents premature belt wear and system failure, ensuring customer satisfaction and vehicle reliability.

How Modern Car Sensors Optimize Performance and Emissions

Learn how Standard ensures accuracy, speed, and durability in their sensors to maximize engine performance and efficiency.

Charging More May Bring Customers Back

Here’s why charging more for brake jobs keeps customers coming back.