What Is Behind Wheel Bearing Noise?

What Is Behind Wheel Bearing Noise?

A caliper that’s sticking or a brake pad that’s loose and dragging may make a metallic scraping noise.

Many drivers will hit a whopper of a pothole yet, on the other side, the wheel bearing will remain silent. But a week later it is singing and growling. For a shop diagnosing the noise, isolating brake, drivetrain and bearing noise on a high mileage vehicle is difficult. 

The classic symptom of a bad wheel bearing is typically a cyclic chirping, squealing or growling noise that changes in proportion to vehicle speed. The sound may appear or disappear only at certain speeds. The noise may get worse when turning, or it may disappear momentarily. So, it’s difficult to make a diagnosis based on noise alone.

A caliper that’s sticking or a brake pad that’s loose and dragging may make a metallic scraping noise as it rubs against the brake rotor. The frequency of the noise will also change in proportion to vehicle speed, but will often go away or change when the brakes are lightly applied.

Noise that only occurs when braking is likely a brake problem, such as worn pads, not a bad wheel bearing.

A popping or clicking noise when turning is a classic symptom of a bad outer CV joint. Also note the condition of the CV joint boot. If torn or leaking, the boot should be replaced regardless of the condition of the joint. If the CV-joint is noisy, it needs to be replaced. A complete axle shaft with new or remanufactured joints on each end is the fastest fix for this kind of problem.

When a vehicle hits a curb, pothole or other object in its path, the force is transferred to the small surface area of the bearing. The impact may cause damage to the races and the rollers/balls. This damage is called brinelling.

Brinelling is a material surface failure/defect caused by contact stress that exceeds the material’s hardness limit. The result is a permanent dent or “brinell” mark.

If a wheel is making noise, the brakes, wheel bearings and CV joint should all be inspected to determine the cause, as all pose a potential safety risk. Any parts that are worn or damaged must be replaced.

It is nearly impossible to give a general torque specification for a locking nut torque specification or procedure. There can be large differences depending on bearing type and housing. Also, different vehicles have different vehicle loads on the wheel ends. But, there are some general best practices that technicians should follow.

The first best practice is to always check the service information from the bearing manufacturer or the OEM for the correct procedure.

Over- or under-torqueing a bearing is a common error that can lead to premature failure. Also, the same bearings can be damaged by a procedure that may work for another vehicle.

The most neglected components during bearing repair are the stub axles and splines. This area serves many functions. It connects the transmission to the wheel end and is responsible for transmitting power to the road. Also, the inner and outer flanges transmit the load on the bearing and pre-load the bearing. The flanges of the stub axle have about the same surface area as a business card, but they carry a lot of the load. Any imperfections will change how the bearing performs. Replacement flanges and stub axles are available.

Clean and inspect the axle shaft prior to installing a new hub assembly. Use a fine file, wire brush, emery cloth or honing stone as appropriate to remove any debris, nicks or burrs. Don’t use any lubricants on the threads or washers. This can change the torque readings.

Don’t reuse the old hub nut on the axle if possible. Install a new one and torque to bearing or OEM specifications. These nuts are specifically engineered to not loosen over time. Some use metal fingers or bands designed to deform and grip the axle shaft.

While impact wrenches can make the job easier, they could cause damage to more than just the bearing. If you are using an impact wrench to remove the axle nut, you can damage the needle bearings on CV joints. While an impact wrench may not seem as powerful as the engine, if the suspension is at full droop, the angles of the joint could damage some of the delicate needle bearings. Also, the rattling caused by an impact wrench is not good for the differential.

In a perfect world, wheel bearings would outlast the vehicle. But, rarely does a bearing just wear out due to the wheel spinning. When a bearing needs to be replaced, it is usually a case of inadequate lubrication where the seal failed or an impact wrench damaged the bearing surfaces.

You May Also Like

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.

The most challenging wheel bearing to replace is a cartridge or press-fit, otherwise known as a gen 1 wheel bearing. No matter what you call them, gen 1 wheel bearings can be found on domestic and import nameplate vehicles. Removing and installing these bearings requires the correct tools and patience. 

Tapered Wheel Bearings

Here’s what you should know as a technician when servicing tapered wheel bearings.

Understanding Passive Wheel Speed Sensor Operation

Passive types of wheel speed sensors are still used in many applications so understanding their operation is important.

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

How Regenerative Brakes Operate

Regenerative braking is a hybrid’s first choice for braking.

Other Posts

Electric Power Steering Diagnostics

Load management for steering systems.

Live Axle Wheel Bearing Service

Replacing rear wheel bearings on a live axle rear suspension requires a few extra steps when compared to a unitized bearing.

Tesla Wheel Bearing Replacement

The process of replacing the hub unit on a Tesla is the same as many cars and light trucks.

Brake Pad Edge Codes – What Can They Tell You?

The edge code is a language written by engineers, federal entities and industry associations.