What causes a P0420 code?

What causes a P0420 code? (VIDEO)

If the front signals and the rear signals look identical, the catalyst is not doing its job. Sponsored by AP Emissions.

A recent EPA study showed that 7% of cars in the United States were operating below federally mandated emissions. 68% of those emissions failures were due to PO420 or 430 catalyst system inefficiency below threshold OBD 2 Code.

When a catalytic converter is working efficiently under closed lube operation, the front oxygen sensor will typically show an airfield mixture switching between rich and lean, rich and lean, rich and lean over a fast timeframe, as the car works to maintain a combustible airfield mixture, that’s optimal for the most power with the least emissions.

However, the signal from the rear 02 sensor that monitors that catalyst should not switch very much between the rich and lean. It should go basically a straight line when that converter is operating efficiently. The takeaway here is that if the front signals and the rear signals look identical, the catalyst is not doing its job.

When you start a car up, you can see the rear sensors showing fuel trim switching, between rich and lean. Older cars with front 02 sensors switch much more noticeably than newer cars with front air fuel ratio or lambda sensors.

Once that catalytic converter is warmed up, oxygen is alternately stored and released by the catalytic converter to maintain that catalytic converter reaction process. So until that catalytic converter is warmed up, both the front and the rear will switch between rich and lean over a fast timescale. The front will look like a mirror of the rear until the cat lights off and starts doing its thing. Then, after it’s all warmed up, it should be a mostly straight line out the rear. If the car’s all warmed up and you’re still seeing the rear sensor mirror that front, then your converter is not working properly. A 420 or 430 code, depending on which bank is triggered when the computer senses that the rear is switching more than it should. It knows this by comparing the signals of the rear catalyst monitor with the signals from the front air fuel ratio or oxygen sensor.

Sometimes manufacturers change the trigger point for 420 code by issuing an emissions related technical service bulletin and release an ECM flash update that loosens the trigger point for catalyst inefficiency code.

Catalyst system efficiency below threshold codes are usually caused by a failed catalytic converter. Sometimes it can be result of faulty sensors, circuit problems, an exhaust leak, or computer issue that needs updating.

A catalytic converter is a simple device. It’s got no moving parts and it rarely fails on its own. When a catalytic converter fails and you get a P0420 or 430 code, it’s the technician’s job to put on their detective hat and figure out what killed the cat.

In the next four videos, we’re going to discuss catalytic converter thermal damage and poisoning. Then we’ll review some diagnostic tips, grouped for simplicity under the traditional conceptual headings of air fuel and spark.

This video is sponsored by AP Emissions Technologies.

You May Also Like

EV Safety Basics on the Shop Floor – Part II

As long as you follow the EV guidelines, you are going to have to use the proper PPE and insulated tools.

Staying safe while working on an electric vehicle requires the correct shop equipment as well as the correct personal protective equipment (PPE) and shortcuts are simply not an option. Let’s take a look at everything you are going to need.

We’ll start with PPE and electrical safety gloves. Class zero electrical insulating gloves rated for 1000 volts are required for EV service. Simply put, these gloves prevent high voltage from traveling through your hands, and they must be tested every time you use them by checking for a pinhole or any damage that could allow voltage to pass through a glove. A glove inflator is the most efficient way to do this. Insulating gloves must also be clean and dry so there are no conductive substances that can allow high voltage to travel outside the glove to your arm. Treat these safety gloves with extreme care. They can be damaged easily and they’re sensitive to UV rays, so they should be stored in a dark, dry environment. A ventilated UV-resistant bag is the best option. Safety gloves must also be re-certified every six months. You’ll also wear them with a leather outer glove to protect them, most prefer to wear an inner cotton glove as a liner to allow your hands to breathe.

EV Safety Basics on the Shop Floor – Part I

It’s critical to utilize OEM service information and procedures for each and every hybrid or EV.

Autel MaxiSYS Ultra Enhances Efficiency At Mighty Auto Pro

Time is money in vehicle repair, and the Autel MaxiSYS Ultra is all about enhancing technicians’ diagnostic prowess.

Empowering the Automotive Aftermarket Through Collaboration

Distributors, manufacturers, training institutions, associations and service providers all help automotive professionals stay ahead in a market that is constantly evolving with new technologies, trends and customer demands.

Understanding LSPI & Engine Oil

Using the correct manufacturer-recommended oil is crucial for peak performance and long-lasting engine health.

Other Posts
Randy Breaux, Group President, GPC North America, Talks to AMN Drivetime

At NAPA, “Breaux Knows” business relationships, ABCs to avoid, and serving the automotive professional.

Serpentine Belt and Drive System Maintenance

Properly maintaining the entire drive system prevents premature belt wear and system failure, ensuring customer satisfaction and vehicle reliability.

How Modern Car Sensors Optimize Performance and Emissions

Learn how Standard ensures accuracy, speed, and durability in their sensors to maximize engine performance and efficiency.

Do EVs Require Special Brake Pads?

Proper brake pad selection is crucial for EVs to ensure consistent stopping power and long pad life.