Toyota Tundra Brake Job

Toyota Tundra Brake Job

For 2007, the Toyota Tundra was redesigned. The body changed, and the foundation brake system was also updated with larger front brake calipers and rear disc brakes. The control system and hydraulics changed with a new vehicle stability system that included yaw, steering angle and brake pedal load sensors.

toyota diesel brake 1For 2007, the Toyota Tundra was redesigned. The body changed, and the foundation brake system was also updated with larger front brake calipers and rear disc brakes. The control system and hydraulics changed with a new vehicle stability system that included yaw, steering angle and brake pedal load sensors.

Overall, this is one of the easier brake jobs. Changing the front brake pads does not require the application of lubricants. The rear brakes are a lot easier to service when compared to the previous models.

toyota diesel brake 2Front Brakes

The front brakes use the typical Toyota truck four-piston caliper found on the previous generation. The pads are held in with pins that have an anti-rattle clip on the lower pin and a pin holder clip. These items should not be reused when replacing the pads. A quality pad set will include these in the box.

Toyota has designated the bolts that hold the caliper to the knuckle as non-reusable parts. Replacement bolts are readily available. Some remanufactured calipers include new bolts.

When removing the pads or pushing back the pistons, use the correct tool. A brake pad spreader can not only save time, but also prevent damage to the piston boots.

The OE friction formulation on the Tundra is ceramic. A replacement brake pad should be of a similar formulation.

The original pads on the Tundra come with shims. Do not lubricate the back of the pad with any lubricant. The lubricant will only transfer onto the piston boots and cause them to attract debris. This can lead to an early failure.

Pulsation is an issue with some 2007-2009 Tundra models. Most of the issues are related to excessive runout or uneven deposits of friction material on the rotor. The runout specification on the Tundra is .05 mm or .002”. The hub flange should have almost zero runout.

Rear Brakes

The 2007 Tundra is equipped with disc rear brakes with the parking brake in the hub. The caliper is a floating design with a single piston. The OE friction formulation is ceramic. The OE backing plate uses a clip-style shim.

According to Toyota, the abutment clips and guide pin boots are non-reusable parts that should be replaced if the pads are serviced. The guide pins should be lubricated with a brake-specific lubricant that is not petroleum based.

Parking Brake

To adjust the parking brake, insert an adjustment tool into the adjustment hole on the disc.

1. Rotate the adjustment wheel in the “X” direction until the shoes are locked.

2. Rotate the adjustment wheel in the “Y” direction eight notches.

3. Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the “Y” direction and check again.

4. Install the hole plug.

Tundra TSBs

Parking Brake Noise (T-SB-0013-13)

Years: 2007-2012

Condition: Rubbing or grinding noise from rear on turns

Summary: This TSB covers an issue with the parking brake mechanism and rear axle bearings causing the rotor to make contact with the parking brake backing plate. Toyota introduced kits 04002-4310C (right) and 04002-4320C (left) to resolve the problem. The kits includes new bearings, backing plate and associated parts.

Front Brake Vibration at High Speeds (T-SB-0131-12)

Years: 2007-2012

Condition: Front brake vibration when braking at higher speeds.

Summary: This TSB covers an updated dust shield that is ventilated and is designed to dampen the vibration. To install the new shield, it requires removal of the hub assembly. You are probably better off looking at disc thickness variation and runout before ordering the updated parts.  n

You May Also Like

Axle Torque Procedures

Guessing the correct torque setting is a bad idea.

The physics of all threaded fasteners are the same. As the bolt and nut are turned, the spiral threads convert rotational force into a linear force that creates clamping loads. When a threaded fastener is tightened, it stretches. Since metal is elastic, even greater clamping loads are generated. The threads also generate friction that keeps the assembly together. This especially applies to wheel bearings and axle nuts.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.

Tapered Wheel Bearings

Here’s what you should know as a technician when servicing tapered wheel bearings.

Understanding Passive Wheel Speed Sensor Operation

Passive types of wheel speed sensors are still used in many applications so understanding their operation is important.

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

Other Posts

Please Take Our Brakes/Rotating Electrical Survey

By entering, you’ll have a chance to win a $100 gift card or one of 10 $25 gift cards!

Replacing Master Cylinders

The most common problems that occur in the master cylinder are wear in the piston bore and piston seal failure.

April’s ShopOwner Brings May Business Success

Read the new edition online now for solid business, technical and management information for your shop.

Why Brake Pads and Rotors Should be Replaced Together

Brake pads and rotors should always be replaced in pairs.  Pairing new pads with worn rotors could cause a lack of proper surface contact between the pads and rotors, resulting in noise, vibration, or less-than-peak stopping performance. While there are different schools of thought on this paired part replacement, at ADVICS, our technicians always recommend