Top 10 Brake Job Mistakes

Top 10 Brake Mistakes

Here are the top 10 most common brake job mistakes made by rookie mechanics when replacing brake pads, rotors and calipers.

  1. Not cleaning the brake slides and hardware: Just slapping new pads and abutment clips where the old ones once resided never works. The caliper bracket slides need to be clean and free from rust.
  1. Not lubricating the guide pins: This is a shortcut most pad slappers make. Caliper guide pins on floating calipers should always be cleaned in solvent and new grease should be applied. The grease is under extreme heat and pressure, so always use caliper-specific grease. NEVER put a torn boot back on a car. Failure to service the guide pins is the leading source of uneven pad wear.
  1. Installing the brake pads backwards: It happens more often than you would think! You may get a car in your shop with the owner complaining that the brakes are grinding after a “friend” changed the brake pads.
  1. Not measuring the rotor: Rotor thickness needs to be measured every time. Running a rotor that is below specifications can cause safety issues like cracking and fading.
  1. Not machining the rotor: New pads almost always require a fresh rotor surface so the pads can deposit a thin layer of friction material to increase braking performance. If old deposits of the previous material are on the rotor, it can contaminate the new pad and lead to performance and noise issues.
  1. Not properly torqueing the caliper bracket bolts: Not all caliper bracket bolts are the same. Torque ranges can vary from 30 to 110 ft./lbs. Also, some bracket bolts can be torque-to-yield or require liquid tread lockers.
  1. Over torqueing the caliper guide pin bolts: Caliper guide pin bolts typically need a 13 mm wrench to remove. It is a rookie mistake to go nuts on these bolts and break the heads off. Typically, these bolts require only 25 to 35 ft./lbs. of torque. Be gentle!
  1. Installing a caliper upside down: Nothing is worse than going to bleed a new set of calipers on a vehicle, only to find the bleeders are on the bottom of the caliper and not the top. The bleeder needs to be at the top of the caliper to remove all the air. Always check the box to make sure you have a left and a right before you start the job.
  1. Using cheap brake pads: The most common mistake for rookies is to shop for a pad on price and not quality, features and reputation.
  1. Hanging the brake caliper by the hose: Nothing is more painful than to watch a brake caliper do a bungee jump from a control arm or knuckle and see it dangle by the brake hose. This can cause damage to the internal structure of the hose, which can cause a soft pedal or a rupture.

You May Also Like

Adjusting Parking Brakes

You should never estimate when it comes to parking brake adjustments.

The parking or emergency brake has to perform two distinct jobs. First, it must be able to hold the vehicle on an incline. Second, it must be able to stop a vehicle under a specific distance if the hydraulic brakes have failed. These standards are set by the Department of Transportation (DOT), and the kicker is these standards must be met with the force applied by a little old lady. But, over time, the cables can stretch and the friction materials change their length and thickness, which is why adjustments to the system are required.

Charging More for Brake Jobs

Here’s why charging more for brake jobs keeps customers coming back.

Servicing Multi-Piston Brake Calipers

Caliper replacement may be necessary in high-mileage vehicles because of fluid leaks or because the calipers are sticking.

Wheel Bearings

Higher quality wheel bearings use higher quality steel that is properly heat treated.

EV Brake Jobs

With these vehicles, the major aggravation for shops is brake noise and uneven brake pad wear.

Other Posts

Brake Fluid 101: What Does Brake Fluid Do? What is the Difference Between DOT 3 vs. DOT 4?

When you think about the braking system of a vehicle, you probably think about the major parts you see when removing the wheel: brake pads, rotors, calipers and maybe hydraulics. However, one of the most important parts of the system isn’t visible: brake fluid. Brake fluid comes in several formulations for different applications and plays

Brake Pad Diagnostics

Worn brake pads can tell you a lot about the entire brake system and keep new components from suffering the same fate.

Understanding Passive Wheel Speed Sensor Operation

Passive types of wheel speed sensors are still used in many applications so understanding their operation is important.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.