Tech Tip: Uncovering Source of Nissan Pathfinder Squeak/Creak Noise

Tech Tip: Uncovering Source of Nissan Pathfinder Squeak/Creak Noise

If a 1999.5-2001 Pathfinder exhibits a squeak/creak noise at the right-hand rear shock area while driving, a small stone, rock or pebble may have become lodged between the upper eyebolt of the right-hand rear shock and its mounting bracket. It's also possible for a small rock, pebble ....

If a 1999.5-2001 Pathfinder exhibits a squeak/creak noise at the right-hand rear shock area while driving, a small stone, rock or pebble may have become lodged between the upper eyebolt of the right-hand rear shock and its mounting bracket.

It’s also possible for a small rock, pebble or stone (dia. 15-20 mm) to become trapped in this area and then fall out over time. This would make the incident seem intermittent to the customer.

Use this service procedure to inspect for, confirm and then resolve the incident, if it has occurred.

Service Procedure:
1. Remove the right-hand rear wheel.

2. Remove the upper bolt from the shock absorber (nut=17 mm, bolt head=19 mm).

3. Remove the shock absorber from the upper bracket.

4. Inspect for scrape marks on the painted surface of the eyebolt. This will indicate a rock or pebble was trapped and rubbing in this area. See Fig. 1.

5. Clean the surface of the upper bracket with a shop rag. See Fig. 2.

6. Cut a piece of foam (P/N 73982-4L700) to 30×30 mm (1-1/4” x 1-1/4”).

7. Place the foam inside the upper bracket near the top where the eyebolt installs. See Fig. 3.

8. Reinstall the shock to the upper bracket.

9. Reinstall the nut and bolt to the shock absorber. Bolt torque: 67-88 Nm (6.8 – 7.0 kg-m 49-65 ft.-lb.).

10. Reinstall the RH wheel. Wheel nut torque: 118 – 147 Nm (12 – 15 kg-m, 87 – 108 ft.-lb.).

Courtesy of ALLDATA.

For additional information, visit www.alldata.com.

You May Also Like

Manual Transmission Failure Causes

One of the most common reasons behind why a manual transmission fails is lack of lubrication.

The most common reasons behind why a manual transmission fails are lack of lubrication, incorrect lubrication and improper or no clutch release.

COMPLEXITY OF LUBRICATION

Lubrication should be simple, but in the modern world NOTHING is simple. There was a time when virtually all stick transmissions ran on 90w gear oil. The synchronizer rings were brass or bronze, the cars and trucks shifted around 3,000 rpm and we had 3- and 4-speed transmissions. Ninety-weight did not like cold weather and generated multiple complaints to the manufacturer due to cold-shift problems. You needed two men and a boy to shift one of the units on a cold day until the fluid heated up.

Wheel Bearing Hub Damage Repair

Noise is a classic sign of a bad wheel bearing or wheel hub bearing. Determining why the damage happened may take some time.

Electric Vehicle Battery Service

Don’t be afraid to work on battery packs. However, you should be mindful of the potential damage high voltages can cause.

ADAS Suspension Alignments

Look at the “big picture” and really consider how the vehicle will operate if things aren’t done correctly.

Building The Perfect Future By Mentoring

Share your stories of how you have helped others reach their goals.

Other Posts

Electric Power Steering Diagnostics

Load management for steering systems.

GRI Receives US DOT Certification For Safety

GRI tires will now incorporate the DOT code emboss on its side walls.

Active Ride Control Diagnostics

The key to servicing these systems is proper information and understanding precisely how these systems operate.

Brake Pad Errors and Mismatches

In order to make the right selection, you must do your homework while still remaining skeptical.