Tech Tip: Squeak-Like Sound from Front Bumper Crossmember on Jeep Liberty and Cherokee Vehicles

Tech Tip: Squeak-Like Sound from Front Bumper Crossmember on Jeep Liberty and Cherokee Vehicles

A customer may experience a squeak-like sound when driving slowly over driveway entrances, road bumps or when performing parking lot maneuvers. The squeak-like sound may occur when the vehicle body/frame is flexed (twists). This condition may occur when the front edge flange of either frame rail rubs against the backside of the front bumper crossmember.

Vehicles: 2002 Jeep Liberty and Cherokee models.

Symptom/Condition:
A customer may experience a squeak-like sound when driving slowly over driveway entrances, road bumps or when performing parking lot maneuvers. The squeak-like sound may occur when the vehicle body/frame is flexed (twists). This condition may occur when the front edge flange of either frame rail rubs against the backside of the front bumper crossmember.

Diagnosis:
With the vehicle stopped and in park, slowly rock the vehicle from side-to-side. Applying force to the top edge of the driver or front passenger side door opening may be of assistance. If present, the squeak-like sound will come from behind the front bumper fascia and in the immediate area below either front headlamp.

Another diagnostic method is to set the parking brake, start the vehicle engine, and while in park, slowly turn the vehicle front wheels from side-to-side (to flex the body) while someone listens at the front of the vehicle.

If the above condition is present, perform the Repair Procedure to both the left and right side of the front bumper crossmember.

Repair Procedure:
1. Remove the vehicle front grill and fascia. For additional disassembly and assembly instructions, refer to the Frame & Bumper section of the appropriate 2002 service manual.

2. Remove the screw used to secure the right side frame rail end cap to the front bumper crossmember. The frame rail cap covers the rectangular access hole in the crossmember. Remove the end cap.

1 – Right Side Frame Rail
2 – Weld Lines – already present
3 – Front Bumper Crossmember
4 – Mark line as specified, clamp panels, center punch, drill 3/16 in. holes, add rivets
5 – Draw vertical line 9 mm from inboard edge of rectangular access hole.
5 – Five (5) spot welds – already present.

3. Draw a verticle line from the top to bottom across the width of the front crossmember. The vertical line should be positioned so that it is 9 mm to the right, and parallel to the inboard vertical edge of the right access hole (in the crossmember). See illustration in Figure 1.

4. Mark the vertical line in three places as illustrated. Each top and bottom mark is to be 20 mm (.750 in.) from the top and bottom edge of the crossmemver respectively. The middle mark is to be centered at 50 mm (2.0 in.) from the top and bottom edge of the crossmember.

5. Center punch all three marks to prevent drill bit drift and improperly positioned holes.

6. Position locking pliers through the rectangular hole in the crossmember. Tightly clamp the crossmember panel to the frame rail edge flange. Position the locking pliers so that they will not interfere with the drilling of the three holes or with the heads of the rivets when they are installed.

7. Using a 3/16 size drill bit, drill a hole at each of the three marks made on the vertical line. Drill all the way through both metal panels (the crossmember and frame rail edge flange).

8. Make sure the area around the three drilled holes is free of metal burrs. Install a suitable corrosion-resistant material (e.g. paint primer) to the drilled holes.

9. With the two panels securely held together by the locking pliers, install a rivet (p/n 34201208) in each drilled hole.

10. Remove the locking pliers.

11. Move to the rectangular access hole located at the left side (driver side) of the front bumper crossmember.

12. Perform steps 2 through 10 in a similar manner so that the installed rivets are positioned along the inboard edge of the driver-side rectangular access hole. The left side repair should mirror the repairs made to the right side.

13. Verify that the squeak-like sound condition has been corrected.

14. Install both end caps and screws.

15. Install the front fascia and grill.

For additional information, visit www.mitchell1.com.

Technical service bulletin courtesy of Mitchell 1.

You May Also Like

Brake Hardware

Specific hardware does not do its job if it is left in the box.

Every technician has struggled with those little wire clips that push the pads onto the pistons on some calipers. Those little clips that barely fit into the painted-over holes on the new pads and can shoot across the shop like a rubber band can make a big difference.

Mercedes 4MATIC Diagnostics

The Mercedes-Benz 4MATIC all-wheel drive (AWD) systems have been around for a while now.

Engine Bay Covers: Cosmetic or Comedic?

Each year engine bay covers get bigger and more difficult to remove.

Top Five Brake Tips (VIDEO)

Here are five tips on brake jobs tips for technicians. This video is sponsored by TRW.

Bridgestone Debuts First Ev-Specific Tire

The initial sizes for the Turanza EV tire include fitments for Tesla Model 3, S, X & Y, as well as the Ford Mustang Mach-E.

Other Posts

Artificially Generated Customer Service

As easy as it is to TALK about customer service, actually offering it is NOT automatic. 

ADAS Calibration Aborts

Knowing the common “hiccups” can save you time and money.

Chassis – Ride Control

Learning how to read the tire and communicate your findings is the key to ride control.

Myers Tire Supply Introduces MTS Xpresstm

The innovative solution to consolidate purchases and control inventory costs.