Tech Tip: Silverado's ABS Light Comes on at 40-50 mph

Tech Tip: Silverado’s ABS Light Comes on at 40-50 mph

At speeds over 40-50 mph, some owners of 1999 Silverados may complain that the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time. This tech tip provides information on how to diagnose and repair this condition.

Vehicle: 1999 Silverado.

Customer Complaint: At speeds over 40-50 mph, the ABS and brake indicators come on, and the fuel and volt gauges sometimes drop low at the same time.

The technician had already verified the condition and checked for codes before calling Identifix. He found code C0237 (rear wheel speed signal erratic) stored as a history code but it had not reappeared for him. Next he road-tested with a scanner, watching the vehicle speed input through the powertrain control module (PCM) and electronic brake control module (EBCM) data. When the ABS and brake light came back on, data was lost on the scanner for both the PCM and ABS. Something was crashing the class 2 data line — but what?

On this truck, the instrument panel cluster (IPC), body control module (BCM), EBCM, PCM and automatic transfer case control module (ATC) are all on the class 2 data line at pin 2 of the data link connector. The tech went to the splice pack (SP205) to determine which module was initially causing the problem. The splice pack joins all of the data circuits at one point, and is located on the lower left side of the dash behind the headlamp switch. The splice pack, a connector end with a jumper bar seated into it, is located on a short harness and often is taped to another harness. When the EBCM class 2 data wires were disconnected from the data line, the symptom was gone. Now we knew the EBCM circuit was causing the problem, so that left either a problem with the power/ground or the EBCM.

The tech checked the connector at the EBCM for corrosion and terminal condition — it was OK. Next he removed and cleaned the ground for the EBCM at the frame (see GM bulletin #04-05-25-002A). Using a headlamp to load the circuit, he load-tested the power and ground to the EBCM. The power and ground tested OK, but there was still a problem. A new EBCM fixed this one.

Written by IDENTIFIX GM Specialist Bill Siegmann. Bill is certified ASE Master and L1 with 20 years of diagnostic and repair experience.

For additional tech tips, visit www.identifix.com.

You May Also Like

Mazda Blind Spot Monitor Calibration (VIDEO)

Joe Keene discusses how to calibrate the blind spot monitoring system on a 2020 Mazda 6 Grand Touring.

Whether or not the blind spot sensor itself is damaged, if the rear fascia comes off, a calibration is called for.

Using both the sophisticated electronics of Hunter’s ADASLink diagnostic scan tool and old-school measurements with string and a plumb bob on a 2020 Mazda 6, Joe Keene demonstrates that the key to all ADAS calibrations is precision – and particularly so with blind spot sensors. ADASLink’s onscreen instruction ensures that precision by eliminating guesswork and providing an accurately performed and thoroughly documented calibration for more than 25 million vehicles.

Akebono Releases ProACT Brake Pad Kits for Honda, Ford, Lincoln and Toyota

Electronic wear sensor and premium stainless steel abutment hardware is included in the kits that require it. 

How to Maximize Cooling System Efficiency (VIDEO)

Do everything you can to help the system operate as intended. This video is sponsored by Rislone.

MSU Joins Statewide Effort to Promote EV Mobility Careers

A new a public-private partnership has been established to recruit electric vehicle and mobility talent to Michigan.

Decrypting Brake Pad Edge Codes

Learning the cryptic codes on the brake pad or shoe will tell you a lot of information.

Other Posts

Auto Pros on the Road: Curt’s Service

Detroit-area full-service facility completed an “all-green” expansion for comfort and safety of techs and clients.

Bartec USA To Host TIA’s ATS Class at Their Facility

Classes will be held from April 25-28.

J.D. Power Study: EV Market Growth Fuels Owner Satisfaction

Overall satisfaction with the BEV purchase experience is shifting to more traditional factors, like quality and styling.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.