Tech Tip: Mitsubishi 2-3 Shift Flare, Slipping

Tech Tip: Mitsubishi 2-3 Shift Flare, Slipping

Some customers may complain of shift flare when shifting from second gear to third gear. This bulletin contains procedures for diagnosing and repairing this condition. New, improved parts are listed in the Parts Information section of this bulletin.

Some customers may complain of shift flare when shifting from second gear to third gear. This bulletin contains procedures for diagnosing and repairing this condition. New, improved parts are listed in the Parts Information section of this bulletin.

Affected vehicles: 1997-2002 Mirage, 1999-2005 Galant, 2000-’05 Eclipse, 2001-’04 Diamante, 2001-’05 Eclipse Spyder, 2002-’05 Lancer, 2003-’05 Outlander, 2004 Lancer Sportback Wagon and 2004-’05 Endeavor

Procedure:
1. Test-drive the vehicle to confirm that shift flare occurs at the 2-3 shift.

2. Check the ATF level and color. Correct as necessary. Inspect the A/T drain plug for metal debris.

3. Start the engine and warm the ATF to 140-212° F (60-100° C). With constant throttle opening at TPS reading 1.7-1.8V, confirm that the 2-3 upshift occurs between 35 and 40 mph (between 56 and 64 km/h). Continue this driving pattern until the 2-3 shift has occurred five times.

a. If the shift flare is not eliminated after the 2-3 shift has occurred five times, continue with Step 4.

4. Check for DTCs.

a. If any DTC is set, diagnose the DTC as described in the appropriate service manual.
b. If no DTCs are set, perform the pressure tests for the OD clutch and second brake as described in Group 23 of the appropriate service manual. Record the pressures on the repair order. Then continue with Step 5.

5. Open the rear cover. In the seal ring area, inspect the drum, seal rings and rear cover for grooves, excessive damage and poor clearance. See Fig. 1.

Fig. 1

Note: Perform this inspection/repair with the transmission assembly in the ­vehicle.

a. If any grooves, damage or clearance problems are found, replace the following parts with the new, improved parts listed in the Parts Information chart at right.

– Reverse/OD Clutch Assembly (with drum)
– Reverse Retainer
– Seal Rings
– Rear Cover
– Input Shaft Rear Bearing

b. If no grooves, damage or clearance problems are found, follow the diagnosis procedure in Group 23 of the appropriate service manual.

                                PARTS INFORMATION

Part                                             Model                   Part Number

Reverse/OD Clutch Assembly    Mirage 1.5L             2722A020   
                                                   Mirage 1.8L              2722A019
Rear Cover                                  Mirage 1.5L, 1.8L    MD763204

Reverse/OD Clutch Assembly    Diamante                  2722A017
Rear Cover                                 Diamante                  MD763194

Reverse/OD Clutch Assembly    1999-2003 Galant 2.4L    2722A019
                                                    1999-2003 Galant 3.0L    2722A017
Rear Cover                                 1999-2003 Galant 2.4L    MD763204
                                                    1999-2003 Galant 3.0L    MD763194

Reverse/OD Clutch Assembly    2004-’05 Galant 2.4L    2722A019
                                                    2004-’05 Galant 3.8L    2722A023
Rear Cover                                  2004-’05 Galant 2.4L    MD763204
                                                    2004-’05 Galant 3.8L    MD763194

Reverse/OD Clutch Assembly    Eclipse/Eclipse Spyder 2.4L    2722A019
                                                    Eclipse/Eclipse Spyder 3.0L    2722A017
Rear Cover                                  Eclipse/Eclipse Spyder 2.4L    MD763204
                                                    Eclipse/Eclipse Spyder 3.0L    MD763194

Reverse/OD Clutch Assembly    Lancer/Sportback/Outlander    2722A019
Rear Cover                                 Lancer/Sportback/Outlander     MD763204

Reverse/OD Clutch Assembly    Endeavor 3.8L    2722A017
Rear Cover                                 Endeavor 3.8L    MD763194

Seal Rings                           All vehicles listed above    MD760146, MD760147
Input Shaft Rear Bearing    All vehicles listed above    MD752039 or MR446687

Courtesy of Mitchell 1.

You May Also Like

Simplifying AWD Systems

No matter the manufacturer, there is almost always an all-wheel drive (AWD) option.

No matter the manufacturer, there is almost always an all-wheel drive (AWD) option for most platforms. Most of these systems are designed to be transparent to the driver.

Many AWD systems came onto the market in the 1990s. Unlike 4x4 truck systems of the day, these systems were always engaged and could not be disengaged by the driver. Many of the early systems used mechanical ways to manage the distribution of power to the four wheels. Most of these systems used viscous differentials and limited slip differentials with special fluids inside. These components were prone to failure and are expensive to manufacture. Also, the performance of these systems could be challenging to control with sensors and actuators. Moreover, these AWD systems could cripple fuel efficiency.

Manual Transmission Service

Parts that wear out must be replaced.

Transmission Fluid Hydraulics

You need to know how transmission fluid flows inside an automatic transmission.

Advanced Wheel Bearing Diagnostics

Can a bump set a wheel speed sensor code?

How Well Do You Know Your Driveshaft?

There are three types of modern driveshafts with multiple configurations.

Other Posts

Transmission Service

The following is an example of a dishonest vehicle and how to go about catching it in its lie.

Limited-Slip Differentials And Diagnostics

A limited-slip differential helps to control the tangential forces.

Seven CV Joint Mistakes You Shouldn’t Make

If a CV joint fails, it rarely fails on its own. Outside factors can damage a joint worse than cutting a boot with a knife.

Reprogramming Transmission Control Modules

It’s understandable to have a lot of questions and fears about reprogramming.