Tech Tip: Mazda6 Engine Won't Start in Cold Weather

Tech Tip: Mazda6 Engine Won’t Start in Cold Weather

In extremely cold weather (approximately -30 degrees C), a customer may experience an engine no start/no crank

Models: 2003-’07 Mazda6 vehicles ­produced before Feb. 28, 2007

Note: This tech tip doesn’t apply to MAZDASPEED6 vehicles.

In extremely cold weather (approximately -30° C), a customer may experience an engine no start/no crank ­condition due to a frozen main relay and/or fuel pump relay. Due to the design, moisture can enter the relays and freeze the contact points after ­driving a short distance, and may shut off the engine.

Repair Procedure
1. Verify the customer’s concern.
2. Replace the relay(s) with the modified kits according to the table below.
Note: 2006-’07 Mazda6 vehicles already have a modified fuel pump relay.

Model Year    Repair Procedure
2003-’05         Replace main relay and fuel pump relay with modified kits
2006-’07         Replace main relay with modified kit

Part No.              Description
L3Y1-18-8BX      Main Relay Kit
L3Y2-18-8BX      Fuel Pump Relay Kit (2003-’05 Mazda6 Only)

figure 1Main Relay Kit Installation Procedure
1. Record the customer’s pre-seat radio stations.

2. Disconnect the negative battery cable.

3. Disconnect the air flow sensor connector.

4. (3.0L Engine Only): Disconnect the VAD three-way solenoid connector.

5. Remove the air cleaner.

6. Remove the fuse box lid.

7. Disconnect the main relay from the fuse box, and install an intermediate harness between the fuse box and the main relay.

8. Tie-wrap the intermediate harness and emission harness together.

9. Tie-wrap the intermediate harness and B-terminal harness together.

10. Install the intermediate harness bracket at the
bottom of the fuse box installed location.

See Figure 1.

11. Reinstall the air cleaner.

12. Reconnect the air flow sensor connector.

13. (3.0L Engine Only): Reconnect the VAD three-way solenoid connector.Figure 2

2003-’05 Mazda6:
Proceed to “Fuel Pump Relay Kit Installation Procedure” and install Fuel Pump Relay Kit.
2006-’07 Mazda6: Proceed to the next step.
14. Reconnect the negative battery cable.

15. Re-enter the customer’s pre-seat radio stations.

2006-’07 Mazda6:
Proceed to “Power Window Initialization Procedure” to restore “anti-pinch” and “auto open/close” window features before returning the vehicle to the customer.

Fuel Pump Relay Kit Installation Procedure
(2003-’05 Mazda6 Only)
1. Secure the intermediate harness bracket together with the PCM installation bracket.

2. Tie-wrap the intermediate harness and harness together at three locations. Make sure the intermediate harness passes over the main relay bracket.

3. Disconnect the fuel pump relay from the relay box, and connect the intermediate harness to the fuel pump relay connector.

4. Connect the ground terminal on the body panel with the existing M8 screw.

See Figure 2.

5. Reconnect the negative ­battery cable.

6. Re-enter the customer’s ­preset radio stations.

7. Verify the repair.

Power Window Initialization Procedure (2006-’07 Mazda6 Only)
1. Turn the ignition to the On position.

2. From the driver’s seat, ensure the window lockout switch is not depressed.

3. Press the window switch down to fully open the door window.

4. Pull the window switch up to fully close the door window; hold the switch up for two seconds; release the switch.

5. Move to the front passenger seat and repeat Steps 3 and 4 on the passenger window switch.

6. Verify the proper window operation using each door switch.

Courtesy of Mitchell 1.

You May Also Like

Mevotech Releases 237 New Chassis, Control Arm, Wheel End Parts

The release boosts coverage for domestic and import passenger vehicles, pickup trucks, SUVs and EVs up to model year 2023.

Mevotech announced the addition of 237 new part numbers which expand its premium TTX, Supreme and Original Grade product offerings.

The release significantly boosts coverage for domestic and import passenger vehicles, pickup trucks, SUVs and EVs up to model year 2023, according to Mevotech.

Release highlights include:

10 Timing Belt Tips

Here are the some key installation and service tips to make your next timing belt job just a little easier.

CVT Transmissions

The point here is not to fear a customer complaint about a CVT transmission. 

Mercedes 4MATIC Diagnostics

The Mercedes-Benz 4MATIC all-wheel drive (AWD) systems have been around for a while now.

Transmission Valve Body Service

Four basic items are necessary to start your own reprogramming ventures.

Other Posts

ADAS Module Programming

Reflashing and reprogramming is a necessary service for repairing vehicles.

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

MEMA Celebrates 120th Anniversary

MEMA said the milestone “underscores the association’s enduring legacy and its pivotal role in advancing the future of mobility and the interests of vehicle suppliers.”

UniClutch Launches Clutch System in the United States

From Australian manufacturer Clutch Industries, UniClutch is a clutch system that delivers uncompromised performance.