Tech Tip: Inspecting the Spring-Loaded Automatic Belt Tensioner

Tech Tip: Inspecting the Spring-Loaded Automatic Belt Tensioner

The automatic tensioner has a coil spring inside that applies just the right amount of force against the belt to keep it tight. The tensioner also provides a little "give" so it can absorb and cushion shock loads on the belt that occur when the A/C compressor clutch cycles on and off. What’s more, the tensioner automatically compensates for wear and keeps the belt under constant tension.

By Larry Carley
Technical Editor

Most late-model engines have serpentine belt drives for the engine-driven accessories. And most people know that belts are a maintenance item and eventually have to be replaced. But many don’t know the spring-loaded automatic tensioner that keeps a serpentine belt tight is also a wear item. Consequently, the automatic tensioner may also have to be replaced when the time comes to change the belt.

The automatic tensioner has a coil spring inside that applies just the right amount of force against the belt to keep it tight. The tensioner also provides a little “give” so it can absorb and cushion shock loads on the belt that occur when the A/C compressor clutch cycles on and off. What’s more, the tensioner automatically compensates for wear and keeps the belt under constant tension. But nothing lasts forever, not belts and not automatic tensioners. The typical service life of a serpentine belt is about 60,000 miles or five years. When the belt nears the end of its life, it may become cracked, glazed and noisy.

If an aging belt is not replaced, it may break, causing a loss of drive torque to all of the engine’s accessories. When the water pump stops turning, the flow of coolant stops and the engine begins to overheat. When the alternator stops turning, there is no charging output and the battery starts to run down. When the power steering pump stops turning, the steering suddenly gets very stiff and hard to control.

All too often, an old serpentine belt (or a broken belt) will be replaced with a new one. But the automatic tensioner is not inspected to make sure it is still working properly and is in good condition. This mistake can lead to rapid belt wear and repeat belt failures if the tensioner is weak or worn out.

Belt tension is critical. Too little tension may allow the belt to slip and squeal. Slippage also causes the belt to run hot and age prematurely. And if the belt is really loose, it may come off its pulleys. Too much tension on a belt may overload it as well as the shaft bearings on the water pump, alternator, power steering pump and air conditioning compressor, possibly leading to premature failures in these components.

Belt tensioners were first used back in the late 1970s. These early units were fixed tensioners that required manual adjustment. Then automatic belt tensioners arrived in the mid-1980s. The spring-loaded design eliminated the need for manual adjustments and assured proper belt tension for the life of the belt. Because of this, the tensioner is often overlooked when a belt is replaced. Even so, the tensioner should always be inspected when changing a belt because:

• Rust or corrosion can jam the tensioner housing and prevent it from rotating freely. A frozen tensioner cannot maintain proper belt tension. Corrosion is usually a result of road splash, especially in areas where roads are heavily salted during the winter.

• Dirt or mud can also jam the tensioner housing.

• A loose or worn pivot arm can allow unwanted movement that results in belt noise and misalignment. Over time, this will increase belt wear and lead to premature belt failure.

• A worn bushing in the tensioner pulley can cause vibrations and noise. If the bushing seizes, it may cause the belt to snap.

• A weak or broken spring inside the tensioner can’t maintain proper tension and the belt will slip. Springs lose tension over time from exposure to heat.

• Cracks or damage to the tensioner housing or pulley arm may prevent it from rotating smoothly and maintaining proper belt tension.

SYMPTOMS
Symptoms that typically indicate an automatic tensioner has reached the end of the road include:

• Belt slipping (due to loss of tension).

• Belt glazing (caused by slipping).

• Excessive movement or rocking of the tensioner pulley or “belt flutter” when the engine is running. This means the spring inside the tensioner is weak and/or the bushing is worn. The tensioner needs to be replaced.

• Wobble in the tensioner pulley (or idler pulley). Wobble means the bearings are shot.

• Belt or tensioner noise. The tensioner should be quiet when the engine is running. Any squealing, rumbling, growling or chirping noises should be investigated to determine the cause. A mechanic’s stethoscope can be used to pinpoint the source of the noise. The probe should be placed against the bolt in the center of the tensioner pulley wheel to listen for bearing noise. The idler pulley(s) should also be checked because the bearings in this component can wear out, too. The same goes for all the engine-driven accessories (water pump, alternator, PS pump and A/C compressor).

• Pulley damage. Physical damage of any kind on the automatic tensioner pulley may indicate excessive tension or physical interference. If the pulley is damaged, replace the tensioner assembly not just the pulley. If an idler pulley is damaged, inspect the tensioner also because vibrations caused by a bad idler pulley may damage the tensioner.

TENSIONER CHECKS
Check the movement of the tensioner arm with the engine off. Use a socket with a long handle ratchet or breaker bar on the tensioner pulley center bolt to rotate the tensioner. There are no specifications for measuring the amount of resistance offered by the tensioner spring, but if the tensioner offers little resistance it may indicate a weak or broken spring. If it fails to move at all, the tensioner is jammed and needs to be replaced.

Watch for looseness in the arm when the tensioner is rotated. The arm should not wobble or twist. If it does, the tensioner bearings are worn and the unit needs to be replaced.

Also note the position of the arm on the automatic tensioner. Many units have marks on the housing that show the normal range in which the arm can pivot. If the position of the arm is outside these marks, it indicates a problem (the belt may be too long or too short, or the tensioner may be jammed).

Note the wear pattern on the tensioner and idler pulley(s). Misalignment and bearing wear can cause the belt to track off-center. This will cause the belt to wear quickly. The tensioner and idler pulley bearings can be checked by removing the belt and spinning the pulleys by hand. All pulleys should turn freely with no binding, roughness or wobble. Any binding, roughness or wobble means these parts are bad and need to be replaced.

Pulley alignment should also be checked to make sure there isn’t a mounting problem in the belt drive system. Pulley alignment can be checked by placing a straight edge against the pulleys, or with a special laser alignment tool designed for this purpose.

REPLACEMENT TIPS
If the automatic belt tensioner has failed (and the engine has a lot of miles on it), it’s probably a good idea to replace the idler pulley(s) at the same time. Why? Because the shaft bearings on all the pulleys will have the same amount of wear. If they are reaching the end of their service life, replacing them now will restore the pulleys to like-new condition and reduce the risk of a breakdown because of a belt or pulley failure.

Aftermarket automatic tensioners are often a better replacement choice than an original equipment tensioner, especially on older vehicle applications. Some OEM tensioners (Chrysler 3.0L, 3.3L and 3.8L, for example) were not very robust and have experienced a high failure rate over the years. Rather than simply copy these OEM tensioner designs with their inherent flaws, some aftermarket manufacturers have re-engineered their parts to overcome the weaknesses of the original design. As a result, some aftermarket replacement tensioners may not look exactly the same as the original. But there’s a reason for this — these parts have been redesigned to outperform and outlast the original parts they replace.

A special tool that may be needed when replacing a serpentine belt or automatic tensioner on a transverse-mounted engine in a front-wheel drive vehicle is a special serpentine belt removal tool. The tool has a long, flat extension handle that allows a socket to be placed on the tensioner bolt, so the tensioner in a tight engine compartment, can be easily rotated to relive pressure on the belt. Without this tool, the job is nearly impossible on some vehicles.

You May Also Like

R1234yf: Smaller Footprint, New Diagnostics

The benefit of R1234yf is simple. The new refrigerant lasts only 11 days in the atmosphere compared to 13 years for R134a. This is why the EPA is requiring R1234yf to be installed in all new systems by 2021.

r1234yf featured

The benefit of R1234yf is simple. The new refrigerant lasts only 11 days in the atmosphere compared to 13 years for R134a. This is why the EPA is requiring R1234yf to be installed in all new systems by 2021. The European Union required the changeover on Jan. 1, 2017.
So, what does this mean for independent shop owners and technicians? Currently, there are approximately 20 million vehicles on the road with R1234yf in the HVAC system. It is not a question of if, but when your shop will have to deal with one of these systems. While working on R1234yf systems is not that different from the R134a variety in operation or theory, identifying the refrigerant and recharging the system has some new twists.

Kia Tech Tip: Power Steering Oil Pump Noise

When replacing a power steering oil pump or inspecting a vehicle for a power steering whine noise, inspect the filter screen in the power steering reservoir for contamination.

Chevrolet Tech Tip: ABS Light On, DTC C1233

Don’t always jump to conclusions. A wheel-speed-sensor-related trouble code does not always mean that the sensor itself is faulty. SureTrack provides multiple possible solutions to one problem. In this situation, the problem is code C1233. Scan over this Real Fix and see if it is the right fix for you.

Anti lock brake system
2013 Ford: No Radio, No A/C, Airbag Light On

How many times have you been working on the computer when it suddenly locks up? Not one single key or command works, and the more you click, the less it responds. The only thing left to do is hold down those three magic keys, “Ctrl-Alt-Del,” or shut the whole thing off and restart the computer.

GM Tech Tip: Clunk Or Thump Noise From Front Suspension

Some customers may comment on a clunk or thump noise coming from the front suspension while driving over rough road surfaces. This noise will typically occur when the front suspension is returning to the upward position after a hard downward stroke, such as after driving through a large rut or pothole.

gm-suspension-noise-featured

Other Posts

Tech Tip: Ford/Lincoln/Mercury Transmission Fluid Leak

Follow these tips to diagnose and fix a transmission fluid leak on several Ford, Lincoln and Mercury models. The first step is to remove the LH halfshaft and inspect the halfshaft journal surface finish.

Transmission leak
Automotive Automatic Transmission Filter O-Rings And Lip Seals

Many transmission filters require a seal at the point where they assemble into the transmission. Most of these seals are called “lip seals,” although some filters may use an O-ring. Before filter installation, it is important to make sure that there is no O-ring or lip seal in the case or pump bore left over from the old filter.

BRAKELIGHT: The Car Cradle (March 1986)

Some ideas just never catch on… Related Articles – Welcome To The Future: Are Your Networks Protected? – BRAKELIGHT: BFE Sponsors Soapbox Derby – BRAKELIGHT: Spiffs from the 1970s (1976) I wonder if the Car Cradle paid for itself by shaking out the coins that were trapped in the seats? The ad claims that there

Welcome To The Future: Are Your Networks Protected?

For those of you who do not know me, I will give you a quick download on my background. Related Articles – BRAKELIGHT: Ford Helps Disabled Veterans (June 1951) – BRAKELIGHT: Wreck Display Increases Brake Business 150 Percent (August 1936) – Brakelights: Foam Means Fade (June 1961) I have been playing with cars for 40

cybersecurity