Tech Tip: Faulty Catalytic Converter Can Lead to Lack of Power, Hesitation or Surge

Tech Tip: Faulty Catalytic Converter Can Lead to Lack of Power, Hesitation or Surge

Owners of 2000-'03 Buick Park Avenue 3.8L vehicles may complain of a lack of power, hesitation, surge and/or possible DTC P0420. This can be the result of the catalytic converter degrading and it will need to be replaced. DTC P0420 means the rear oxygen (O2) sensor has too much activity. This means it must be working and therefore the catalytic converter is bad and needs to be replaced. Be sure to perform ....

Vehicle: 2000-’03 Buick Park Avenue 3.8L

Symptom: Lack of power, hesitation, surge and/or possible DTC P0420.

Problem 1 of 3: The catalytic converter has degraded and will need to be replaced.

Test & Fix: DTC P0420 means the rear oxygen (O2) sensor has too much activity. This means it must be working and therefore the catalytic converter is bad and needs to be replaced. Be sure to perform test #3, which addresses a possible cause of the catalytic converter failure.

Problem 2 of 3: The catalytic converter is plugged.

Test & Fix: Check for back pressure at the front O2 sensor. If it is more than 1.25 psi at idle or at 2,500 rpm, replace the catalytic converter. Be sure to perform test #3, which addresses a possible cause of the catalytic converter failure.

Problem 3 of 3: Coolant leakage into the intake manifold causing catalytic converter failure.

Test & Fix: Inspect the intake manifold for signs of coolant. This engine is known for coolant leakage past the intermediate intake manifold gasket and the throttle body gasket. Replace the intermediate intake manifold gasket, the throttle body gasket and the throttle body nuts. Be sure to use medium-duty thread locker. The part number for the gasket kit is 17113137 and the nuts is 11517293.

Courtesy of IDENTIFIX.

For additional information, visit www.identifix.com.

You May Also Like

Tips On Shocks and Struts

Here are 10 basic tips on shocks and struts.

10. Writing An Estimate

To give the customer an apples-to-apples comparison, you may opt to write your estimate in two sections. The loaded strut option, if available, will be very straightforward and require less installation time. For the second section, give the customer a breakdown of the cost for each component required for a complete repair, explaining that each of these pieces is already included in the cost of the loaded assembly. When purchased individually, these components tend to add up quickly and often exceed the price of the pre-assembled unit. Finally, itemize the difference in labor costs, pointing out the additional time required to “rebuild” the strut, which is above and beyond the time already required for removal and reinstallation.

Axle Torque Procedures

Guessing the correct torque setting is a bad idea.

Auto Pros Visit Interstate Auto Care, Madison Heights, MI

For Bill Nalu, business is more than fixing cars – it’s about connecting with people on a personal level.

Constant-Velocity Axle Options

Whether new or remanufactured, complete CV axle assemblies can throw you a curveball from time to time.

All-Electric Fisker Ocean Extreme Achieves 360-Mile Range

EPA values confirm the Fisker Ocean Extreme has the longest range of any new electric SUV under $200K sold in the U.S.

Other Posts

Turning Off The TPMS Light

If a vehicle comes into your shop with the TPMS light on, there are a few key things to check first for time’s sake.

Reprogramming ADAS Procedures

As a vehicle ages, the J2534 programming becomes even more important to the vehicle’s ADAS operation.

Brake Booster Replacement

Hydro-boost vehicles are not hard to work on, but they do require service information and a working knowledge of the system.

AAM to Supply e-Beam Axles for Future Stellantis EV

The future program will feature both front and rear e-Beam axles that include AAM’s integrated 3-in-1 e-Drive technology.