Tech Tip: Electronic Basics

Tech Tip: Electronic Basics

Sophisticated automotive electrical systems can cause increasing amounts of dead batteries, intermittent warning lights and general electrical complaints. When addressing these issues, staying focused on the basics can save you time, money and nerves. Automotive electrical basics are: connection condition; battery condition; and alternator condition.

by The WORLDPAC Training Institute (WTI) Team

Sophisticated automotive electrical systems can cause increasing amounts of dead batteries, intermittent warning lights and general electrical complaints. When addressing these issues, staying focused on the basics can save you time, money and nerves.

Automotive electrical basics are:
• Connection condition;
• Battery condition; and
• Alternator condition.

Connection Condition
In order of importance, connection condition (at least to the battery) really does come first. Without a good solid connection to the battery, the vehicle may not start, charge, or it could generate a few unwanted electrical gremlins. Clean tight connections from the battery to the chassis grounds and to the alternator and starter motor will eliminate subtle electrical gremlins. The condition of all electrical connections and the circuits they connect to can be easily tested using the voltage drop test. You will find bad relays, bad fuses, poor connections and faulty ignition switches within minutes (opposed to hour or days.) This may be the single most important test for technicians to implement into diagnostic routing when searching for a cause to an intermittent electrical complaint.

Battery Condition
Battery condition is paramount on today’s vehicles because the on-board computers will be the first to react to a problem within the battery. Computers are reliant on continuous, uninterrupted current flow between the positive and negative terminals of the battery. One bad plate in the battery can cause a multitude of electrical problems after you start the engine. You may be thinking, “That’s odd, I thought if the battery was bad the starter motor wouldn’t crank the engine?” Not true. As a technician on today’s vehicles, you need to toss out this old thought process. Before addressing electrical complaints on late-model vehicles, check the condition of the battery to ensure it is not the cause of the current fault.

Alternator Condition
After a battery has been determined to be in good condition, you will need to determine the condition of the alternator. With the numerous electronics operating late-model vehicles, the alternator output on some cars may exceed 200 amps! With that much output, the main power lead to the alternator may be fuse protected. Before replacing an alternator because of “no output,” double check the manufacturer’s information regarding their test procedures. You may discover that a fuse, fusible link or specially designed cable is the cause of the no output problem. One other note, be advised that some late-model vehicles could have alternators that are networked and diagnosing them will be different.

Tech Tip courtesy of WORLDPAC Training Institute (WTI).

For additional information on WORLDPAC Training Institute (WTI) and products offered by WORLDPAC, visit www.worldpac.com.

You May Also Like

Non-Competes

The FTC’s rule is set to take effect in about four months, unless it is blocked by legal challenges.

A Non-Starter, Says FTC

As you read ShopOwner, whether it is in print or online, one thing – hopefully – comes across clearly: our mission is to help your shop be more successful.

Sometimes, that is evident through solid marketing advice, updated technical resources or inspirational messages about other successful shop owners who deal with challenges in creative ways. Typically, each issue of our magazine contains all three – and then some.

Eaton Introduces Fuse Portfolio for Electrified CVs

Eaton Bussmann series fuses can handle up to 1,400 amps and 900 volts, and can be tailored to customer specifications.

Succession Planning – Navigating The Legal Landscape

Planning for a successful business handover means doing things by the book.

Genesis Expands EV Availability to 37 States

GV60, Electrified GV70 and Electrified G80 are now available at select retailers in Alabama, Kansas, Oregon and Rhode Island.

Driveshaft, Axle and Drivetrain Noise FAQs

Follow along to learn more about these unwanted noises.

Other Posts

Non-Directional Rotor Finishes

Today, non-directional finishes on new brake rotors still serve the same purpose, but they also help in the bedding of some friction formulations.

PRT Launches 59 New Complete Strut Assemblies

Extending PRT’s product portfolio in North America, the new release represents nearly 12M vehicles in new coverage.

We Want Your Thoughts On Electronic Power Steering

Your opinion matters us and can be profitable for you too! Share your ideas with us.

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.