Tech Feature: GM Tire Pressure Monitoring Systems (TPMS)

Tech Feature: GM Tire Pressure Monitoring Systems (TPMS)

GM TPMS systems on Buick, Pontiac, Chevy (Chevrolet), GMC Cadillac and Hummer models are some of the easiest to service if you have the right tools and knowledge. Starting in 2007, most vehicles use a Schrader- or VDO-manufactured system that shares the same relearn procedures and behaviors. There are exceptions, like the Pontiac Vibe.

The initial “low tire” light is similar to the “low fuel” indicator and Adding air to the low tire will extinguish the light. If the driver re-inflates the low tire, they must drive a short distance for at least 30 seconds before the sensors recognize the increase in pressure and turn the light off again.Shops should use a  TPMS tool reset the sensor positions after rotation. There is a method in the owners manual to “match” the sensors that involves deflating a tire for eight seconds.

On vehicles without a driver information center, you will know you have a code set if you turn the key on, without starting the engine, and the TPMS light blinks for one minute and then stays on solid with a Service Tire Monitor System message (on vehicles equipped with a DIC). If that occurs, a TPM system problem exists and the system will have set a DTC.

On vehicles equipped with a driver information center, it will also display a SERVICE TIRE MONITOR type message. When the road tire is repaired and reinstalled in the original location, the TPM indicator icon illumination and DIC message may remain displayed until the DTC is resolved and cleared.

The initial “low tire” light is similar to the “low fuel” indicator and adding air to the low tire will extinguish the light. If the driver re-inflates the low tire, they must drive a short distance for at least 30 seconds before the sensors recognize the increase in pressure and turn the light off again. If the deflation is rapid, it will give a more immediate warning by flashing the warning light.

A GM TPMS sensor has pressure, temperature and acceleration sensors. The unit also has a radio transmitter, receiver and battery. Sensors have a 10 year /150,000 mile (240,000 km) battery life.
The antenna and receiver is the same one that is used for the keyless-entry system. The antenna is typically sandwiched between the layers of glass in the front or rear glass. But, some vehicles have dedicated antenna mounted in various places.

The keyless entry module communicates with the TPMS sensors and relays the information with the Body Control Module (BCM) on the CAN BUS. If the Keyless entry module is replaced, the sensors must be relearned, same with the key fobs.

Each sensor has its own unique ID number. If a new sensor is fitted, the body control module must  be reprogrammed with its unique ID and its position on the vehicle.

Each sensor takes a pressure measurement sample once every 30 seconds while in stationary mode. If the tire pressure increases or decreases by more than 1.2 psi from the last pressure measurement, another measurement will occur immediately to verify the change in pressure. If a pressure change has indeed occurred, the sensor transmits in Learn mode.

Each sensor has an internal low frequency coil. When the TPMS tool is used in activate mode, it produces a low frequency transmission that activates the sensor. The sensor responds to a low frequency activation by transmitting in learn mode. When the TPMS antenna receives a learn mode transmission while in TPMS learn mode, it will assign that sensor’s ID number to the location on the vehicle relative to the order in which it was learned.

Relearn Tips
• It is best to perform the TPMS relearn procedure away from the shop in the parking lot. This decreases the chance of other radio signals interfering with the relearn process.

• Aim at the sidewall below the valve stem, and not at the stem.

• If you can not get a sensor to initialize, try pushing the vehicle forward a foot or two. The signals can be blocked by components like rotors, calipers and knuckles. By repositioning the sensor, it may unblock the sensor. This is far more common on the front wheels.

TPMS Sensor Matching

1. Set the parking brake.

2. Turn the ignition switch to ON/RUN with the engine off.

3. Press and hold the keyless Entry fob transmitter’s LOCK and UNLOCK buttons, at the same time, for about five seconds to start the TPMS learn mode. The horn sounds twice indicating the TPMS receiver is ready and in learn mode.

4. Starting with the left front tire, active the sensor by holding the  TPMS tool aimed upward against the tire sidewall close to the wheel rim at the valve stem location. Press and release the activate button and wait for a horn chirp.

5. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned will illuminate. On most models, the driver side front turn signal also comes on to indicate that corner’s sensor is ready to be learned. Once the learn mode has been enabled, each of the sensors unique identification codes can be learned.

6. When a sensor ID has been learned, the module sends a serial data message to the BCM to sound a horn chirp. This verifies the sensor has transmitted its ID and has received and learned it. The module must learn the sensor IDs in the proper sequence to determine sensor’s location. The first learned ID is assigned to the left front location, the second to right front, the third to right rear and the fourth to left rear. On most models, the turn signals will individually illuminate indicating which location is to be learned in the proper sequence.

The learn mode will cancel if the ignition is cycled to OFF or if more than two minutes has elapsed for any sensor that has not been learned. If the learn mode is cancelled before the first sensor is learned, the original sensor IDs will be maintained. If the learn mode is canceled after the first sensor is learned, the following will occur:

• All stored sensor IDs will be invalidated in the RCDLR memory.

• If equipped, the DIC will display dashes instead of tire pressures. If the learn mode is canceled after the first sensor is learned, the following will occur:

• All stored sensor IDs will be invalidated in the module memory.

• If equipped, the DIC will display dashes instead of tire pressures.

• DTC C0775 will be set. These conditions will now require the learn procedure to be repeated for the system to function properly.

You May Also Like

The Winter Tire Opportunity – Now Is The Time

Winters tires aren’t just a luxury, it’s your job to tell your customers the positive impact that the tires can give them.

It was a frigid February morning in Chicago last year. The kind of cold that creeps into the depths of your lungs, making it difficult and even a little painful to breathe. The kind of cold that literally takes your breath away. The snow was falling as I stepped into my car and took off across The Chicago Skyway with the city lights in my rear view. It was around Gary, Indiana, that the lake effect snow engulfed Interstate 90 and made it impossible to see the road more than about 15 feet ahead as I made an unwise attempt to pass a massive snowplow in the right lane. And, it was this moment that I understood the difference between an all-season tire and a true winter tire. My life as a “tire guy” would never be the same again.

Diagnosing Audi A8 TPMS Issues

These are all the steps you’ll need to pinpoint fault issues in TPMS for 2009-2016 Audi A8 vehicles.

The Rule of 3X Tire Rotation

Proper rotation procedures maximize tread life and customers coming back.

Communicating The Effectiveness Of TPMS

A good angle to start with may be laying out the consequences of not having a working TPMS.

Servicing Tires With 18-In.-Plus Rims

Servicing any tire and wheel assembly correctly starts with having the right equipment.

Other Posts

ATEQ TPMS Tools Adds Tesla BLE Function To VT67

ATEQ’s new VT67 TPMS Tablet will be capable of reading and programming the Tesla BLE sensor.

TPMS Valve Stems – What Are The Trends? What Is The Future?

Whatever the type of stem, carelessness can result in a broken sensor or even a customer being stranded with a flat tire.

Nissan TPMS Service

The behavior of the TPMS systems is very consistent across all Nissan models.

TPMS Sensor Signals

TPMS sensor signals are low power and low frequency, with most sensors transmitting at 315MHz or 433MHz.