Subaru Steering & Axle Service

Subaru Steering & Axle Service

Here in the Northwestern part of the country, Subaru has become one of the top nameplates. The versatility of the all-wheel-drive system makes them the ideal ski team hauler or beachcomber vehicle. The compact station wagon design is the most popular model, due to its ability to haul people, and their equipment, in comfort and security. For the auto repair industry, Subaru is also a very technician-friendly nameplate, with many different models sharing the same basic design and components.

The parts that separate Subaru out of the ordinary are also the reason they’re so versatile. The flat engine design provides many advantages, including added ground clearance and a compact drivetrain, leaving room for people and payload. The layout of the drivetrain, with its longitudinal, rather than transverse, engine mounting, and straight-through transaxle allows for the addition of all-wheel-drive without major body differences or cumbersome transfer gears.

Subaru has packed a lot of drivetrain and accessory pieces into a compact area, but the layout is such that with a little planning, most drivetrain and suspension repairs are easily completed. The Legacy series (including Impreza, Outback and Forester) from the early 1990s-on are the most common models we see and, except for some improvements, repairs are pretty much the same on all of them, up to the current models. This article will focus on some of the more common repairs we do and a few tips to make them easier.

STEERING
I haven’t seen a Subaru without power steering in years, but it’s no surprise that we do have to change a power steering pump or rack-and-pinion once in a while. Subaru has made the pump on these cars one of the easiest to replace of any car. Unfortunately for us, they don’t fail. Usually the only problem is a leak between the reservoir and pump body. While the seal is easy enough to replace, we’ve had some recurring failures because the seal is difficult to seat. Just use care, and a little silicone paste, to make assembly easier.

In some cases, pump replacement is necessary after years of running low on fluid and noise complaints. The replacement procedure is typical, as stated in the repair manuals: Loosen the drive belt, remove any hose and mounting bolts as needed, and reverse to reinstall. This is one repair where the instructions are pretty accurate. The one item I would add is to use a flush machine, vacuum bleeder or other method (Turkey baster? Probably not. Your spouse may not be too happy with you at Thanksgiving) to suck as much fluid out of the reservoir as possible to reduce the mess and keep fluid off of the other belts.

On the other end of the steering hose is the steering rack. It’s tucked into a crossmember that runs under the engine pan (see photo 1). It is well protected from damage by that crossmember, as well as the exhaust. Even the rack end boots are pretty well out of harm’s way (see photo 2). Rack replacement can be easily facilitated by first removing a couple of other items.

  1. Make sure the steering wheel is centered; lock in place, if possible.

  2. Remove the front exhaust pipes (see photo 3). Remember to disconnect the front O2 sensor, and then separate it at the catalytic converter and remove the nuts at the headpipes to the cylinder heads. Removing the exhaust as a single piece saves broken-off bolts and additional time.

  3. Measuring the toe at this point will make alignment easier after the new rack is installed. Disconnect the tie rods at the steering knuckles. Another way to retain steering angles and toe is to pull back the rack boots and disconnect the tie rods at the inner end. Leave them attached at the knuckles, that way the toe shouldn’t change significantly.

  4. Make a reference mark on the steering shaft so that you have a position for the centered steering wheel. Loosen the pinch bolt for the steering shaft to pinion shaft joint.

  5. Disconnect and drain the lines from the pump.

  6. On some models, removing the sway bar bracket retainers and swinging the sway bar out of the way may be necessary (removing the sway bar completely is easy as well). Then remove the mounting bolts for the rack and remove it.

  7. Depending on whether you’ve got a long or short rack for replacement, transfer necessary items from the old to new and reverse the procedure to reinstall. If you are installing a long rack, remember to measure from tie rod end to tie rod end for basic measurement. With a short rack, just transfer the entire tie rod assembly, leaving the adjustment “as is.”

  8. Inspect the mounting bushings for cracking or oil damage, and replace as needed.

  9. After reconnecting everything, refill the system with the proper fluid and bleed. Recheck all fasteners and then reset toe to specs. Make sure the steering wheel is still centered and road-test.

AXLES AND CV JOINTS
As with all front-wheel-drive cars, the axles will need service, repair or replacement from time to time. Subaru has used the same basic axle design on all of these cars for the entire model run. They are fairly short, of equal length and are durable.

Considering the typical use of these cars for recreation, the number of axle problems are not excessive. The inner boot on the passenger side is the most susceptible to damage, mostly due to its proximity to the exhaust. Inner boot replacement on the left (driver’s) side can be accomplished without axle removal, but unless mileage is low and there hasn’t been any hint of noise, axle replacement is probably a better idea.

Rear axle or boot replacement is very unusual, mostly only due to damage or off-road use.

Front axle replacement goes as follows. I’ll use the right side as an example, because it’s the most difficult. This can be done on the floor, with the car properly jacked and secured with jack stands, but is much easier on a hoist.

  1. Remove the wheel and tire assembly. Remove the axle center nut. Spray the splines with penetrant fluid.

  2. Remove the pinch bolt from the steering knuckle, spray the ball joint body with penetrant and pry the ball joint body out of the knuckle (see photo 4). This can be an easier task if you remove one of the bolts from the sway bar link to allow additional lower control arm movement.

  3. Turn the steering knuckle to the full right position to move the steering arm out as far as possible. Push, tap or rattle the axle out of the hub while applying outward pressure to the knuckle. This can all be done with the brakes in place if caution is used. The flex line for the brakes is just long enough to allow for removal of the axle from the hub. Also use care with the wiring harness for ABS-equipped cars. In really tough cases, you may need to press the axle out with a hub fixture and push bolt.

  4. Remove the roll pin at the transaxle. This can be a challenge on the right front. From underneath, there is a hole between the crossmember, exhaust and O2 sensor that works well for aligning and removing the roll pin. I use a correct size (7/32”) roll pin punch and a socket extension to remove the pin. The last tap will send the pin into some unknown black hole, so be ready.

  5. The axle can now be removed from the splines at the transaxle, and removed to the outside. Compare the length, spline count and shaft size to the replacement and reverse the procedure to reinstall.

  6. Due to the restricted space on the right front, use care with the new axle to prevent damage to the boots when installing. Line up the roll pin holes in the inner joint and transaxle output shaft and slide into place. Normally one of the holes in the inner joint will have a countersink, which will make starting the roll pin easier.

After a light tap to start the pin, tap the pin through, noting that the pin must stay aligned and also pass through the output shaft. Install until the pin is just flush with the joint housing on the other side. Use your judgment that the pin fits tightly enough to stay put. If the pin went in too easily, now is the time to replace it. Note that some new pins supplied by axle vendors can be enough oversize to make them very difficult to install.

CV boot replacement is fairly simple if joint damage is not suspected. To replace the outer boot, the inner joint and boot must be removed as the outer joint usually isn’t easy to separate from the axle shaft. The outer shaft or joint may be damaged if disassembly is attempted. As noted above, if the inner left side boot is torn, it can be replaced while on the car, just by separating the knuckle at the ball joint as noted, then pulling the axle off of the transaxle output splines.

The inner tripod joint can be removed by removing or pulling back the boot at the joint and then removing the inner circlip that acts as a stop to prevent the joint from separating. With the clip removed, the tripod trunion and bearings (free rings) can be removed from the housing. It’s best to keep the tripod bearings on their respective pins and the bearings in the same races in the housing, so marking everything as you disassemble is important for joint life after reassembly. With the bearing assembly out of the housing, remove the external circlip that holds the tripod axle in place on the splined shaft and slide the tripod off. Marking position is again important to prevent vibration problems.

Now the inner boot, then the outer boot can be removed and replaced. Be sure to look for dirt or water in the joints, and repack with enough CV grease to provide lubrication, but not so much that there isn’t any expansion space inside the boot. This may cause excess grease to be pushed out or the boot to dislodge. Reinstall the boot retaining bands with a proper crimping tool. Work the joints in all directions before reinstalling the axle, just to make sure there is no hint of binding. The joints should feel tight but with no “hitches,” which could cause noise or vibration.

REAR SUSPENSION
The rear drive and suspension systems are very uncomplicated. One job we do fairly often is rear wheel bearing replacement. This is a typical type of pressed-in duplex bearing that can be removed with an on-car bearing press tool. To remove the axle for access to the bearing, remove the long front-to-back bolt that positions the outer end of the lower control rods. This will allow enough movement to angle the axle up or down to provide room for the press tool.

The rest of the process is just like most front-wheel-drive cars with this type of bearing. Before going any further, I caution you to look at the location of the ABS components, in particular the wheel speed sensor. Sometimes it’s in the housing and reads off of the outer CV joint housing. On some models, the sensor is in the backing plate and reads a tone wheel on the wheel hub. In either case, be careful not to damage the sensor or tone wheel.

  1. Use a slide hammer to remove the wheel hub. Inspect the hub for any evidence that it was spinning in the bearing, and just test-fit it into the new bearing to be sure it will be an interference fit. If it just drops into the new bearing, replace the hub or get the correct new bearing.

  2. Remove the two inner seals (one is a dust seal; the other keeps grease in the bearing).

  3. Remove the outer seal if it didn’t stay with the hub when it was removed.

  4. Remove the circlip from the bearing housing. Spray around the outer edge of the bearing to ease the pulling process.

  5. Use a bearing press set to pull the bearing out of the housing from the outside. Be sure to use a small diameter adapter on the inside that will fit through the housing.

  6. Clean the inside of the housing and lubricate the bearing recess. Use the bearing press to push the new bearing in from the outside by using a larger diameter inner adapter or, if space is available, pull the bearing in from the inside. Reinstall the bearing retainer circlip into the housing.

  7. If the outer bearing race stayed with the hub, press or rattle it off of the hub before you press the hub into the new bearing. Also, if you are replacing the hub and it didn’t come with the tone wheel for ABS, be sure to transfer it from the old hub before you put it on, or you’ll need another bearing when the ABS light comes on.

  8. Reinstall the axle, torque the retaining nut to specs and stake in place. Road-test the vehicle and make sure the ABS light stays off.

FINISHING UP
Subaru continues to improve and upgrade its models to stay current with other vehicles in its classes. They manage to do this while maintaining quality and consistent construction. This all adds up to technician and shop friendly cars that meet the needs of the customer.

Keep Subaru customers happy, and they will most likely maintain their cars and keep them much longer than other models. If you haven’t started servicing Subarus in your shop, now is the time to get familiar with them.

You May Also Like

MEMA Celebrates 120th Anniversary

MEMA said the milestone “underscores the association’s enduring legacy and its pivotal role in advancing the future of mobility and the interests of vehicle suppliers.”

MEMA, The Vehicle Suppliers Association, announced its 120th anniversary, a milestone it said "underscores the association's enduring legacy and its pivotal role in advancing the future of mobility and the interests of vehicle suppliers."

MEMA was founded on March 2, 1904, in Cleveland, Ohio, to represent the burgeoning automotive parts manufacturing industry. For the last 120 years, MEMA and its members have been at the forefront of advocacy, innovation and collaboration, the association said.

UniClutch Launches Clutch System in the United States

From Australian manufacturer Clutch Industries, UniClutch is a clutch system that delivers uncompromised performance.

MEMA Aftermarket Suppliers Becomes UAF Gold Lifetime Trustee

The partnership with UAF is a commitment to the future of the automotive aftermarket, MEMA Aftermarket Suppliers said.

Castrol Turns 125, Debuts New Market Strategy

As part of the new strategy, Castrol will explore opportunities in battery thermal management, digital and service solutions and data center immersion cooling.

FCS Introduces 18 New Numbers in February

The new release includes 4 shock absorbers and 14 suspension struts.

Other Posts

Philips Releases GoPure Advanced Automotive Air Purifier

It filters out 99% of bacteria and respiratory viruses and fits in the cupholder.

AP Emissions Releases New Part Numbers for February

The 12 new SKUs cover 6 million VIO.

MANN+HUMMEL NA Aftermarket Shows Right to Repair Support

Representatives from MANN+HUMMEL’s North American aftermarket brands recently visited Capitol Hill to express their support for H.R. 906.

Federated Upgrades Car Care Center Program

The enhanced program features updated signage, marketing support, image-enhancing tools, wearables, business management assistance and other information to help with day-to-day shop operations.