Rotor Metallurgy

Rotor Metallurgy

In the past few years, the prices of rotors seem to be dropping. Call just about any parts supplier and they can quote you a vast range of prices for the same application. When you compare the rotors side-by-side, they may look the same. But, the difference between a comeback and satisfied customer might be at the microscopic level.

Just about every rotor is made of cast iron. But, what can make or break a rotor are ingredients like carbon, silica and pearlite. Also, how a rotor is cast and cooled can determine its final properties. This is called the science of metallurgy.

Ensuring that a rotor has the right metallurgy costs the manufacturer time and money. It is not that the raw material costs more, it is that the manufacturing process may require more expensive equipment. Also, the energy costs and labor costs may be higher

You may be saying, “iron is iron.” This is not true when it comes to brake rotors. OEMs use different grades of iron to ensure that a vehicle platform has the right characteristics of wear, noise dampening and performance. Like brake pads, rotors can be vehicle specific.

Taking a chance with some “cheap,” “economy” or “inexpensive” aftermarket rotor that does not use the right grade of iron or manufacturing process could end up in a comeback.

Microstructures
Talk to any metallurgist or materials engineer and they will inevitably mention microstructures. What they are talking about is how the atoms and molecules bond or connect with each other to form small cohesive structures.

Think of these microstructures as a tiny racecar roll cage. A strong roll cage joins to the chassis at many points and the bars intersect at many joints. However, a weak roll cage will have fewer bars and joints. The stronger roll cage is able to resist being torn apart because it has more connections and stronger bonds. Also, a well-designed roll cage can influence the overall performance of the vehicle.

The same can be said about the cast iron mix that makes up a rotor. How the iron interacts with other elements like graphite (a form of carbon), silica and other materials can influence the microstructure of the iron and influence the final product. These microstructures can influence properties like wear, coeffeicent of friction and noise control.

Metallurgist can fine-tune the mix of iron and element to give a rotor the right characteristics for a vehicle. If more graphite is added to a mix, it can improve the noise damping properties of the rotor. But, the increased graphite content can lower the rotor’s resistance to wear and abrasion. If the wear characteristics need to be improved, a substance called pearlite can be added to the mix.

To achieve the best performance of the rotor, it is a balancing act. Adding too much of a component can ultimately affect the rotor’s ability to generate friction and dissipate heat.

Stress and Heat
Casting rotors can stress them out. Going from cold raw material to a hot liquid, then cooling into a new shape causes stress in the raw casting.

The microstructure of the rotor contracts as it cools. If one area of the rotor cools faster then an adjoining area, stress is created between the two areas due to the different rates of contraction. As you can imagine, rotors with large hats or a large swept area have areas that cool at different rates.

This stress can influence the performance of the rotor under heat and mechanical forces. This includes warping and mechanical failure. In other words, this stress could cause you the stress of a comeback in some cases.

To avoid these problems for some applications, a reputable rotor manufacturer will perform a process called stress relieving. It is a process where the fresh cast rotor is kept at a constant temperature for a certain length of time. Stress relieving is typically performed in the temperature range of 500

You May Also Like

Non-Directional Rotor Finishes

Today, non-directional finishes on new brake rotors still serve the same purpose, but they also help in the bedding of some friction formulations.

Back in the day, a non-directional rotor finish was the method used to solve a common problem that occurred on bench brake lathes. If the crossfeed speed was too fast, the rotor became like a vinyl record, and the pads became the needle that followed the grooves in the record. This would cause a clicking noise as the pads moved in the caliper as it followed the concentric grooves.

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.

Wheel Bearing Service

When faced with any noise complaint, take the time to test-drive the car with the customer, if that’s possible.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.

Tapered Wheel Bearings

Here’s what you should know as a technician when servicing tapered wheel bearings.

Other Posts
Do Severe Duty Brake Pads Trade Power For Longevity?

Accepting reduced component life for better braking power in severe-duty applications may be a thing of the past.

HELLA PAGID Launches Semi-Metallic Brake Pad Line

Global automotive brake systems supplier HELLA PAGID announced the launch of its latest product line of semi-metallic brake pads.

Please Take Our Brakes/Rotating Electrical Survey

By entering, you’ll have a chance to win a $100 gift card or one of 10 $25 gift cards!

ShopOwner’s May Digital Edition Is Available Now

Free to download and read, priceless in business value.