Relearn Procedures Require TPMS Tool

Relearn Procedures Require TPMS Tool

Most vehicles require some type of "stationary" relearn procedure to reset the TPMS system. This requires a TPMS tool to activate each of the tire pressure sensors in a specified sequence so the TPMS control module can relearn their new locations.

Most vehicles require some type of “stationary” relearn procedure to reset the system. This requires some type of TPMS tool to activate each of the tire pressure sensors in a specified sequence so the TPMS control module can relearn their new locations. On some GM applications, a J-41760 magnetic tool is required to “wake up” the sensors. On most other applications, a factory TPMS tool or an aftermarket TPMS tool that broadcasts a radio signal is needed for the sensor position relearn procedure.
 
On some applications, the TPMS relearn tool can be connected to the vehicle’s OBD II diagnostic connector to read and clear codes, display system data and perform sensor ID programming. On many Asian and
European applications, each individual tire pressure sensor has a unique ID code. Vehicles that currently require this kind of reprogramming include most Hyundai, Infiniti, Kia, Lexus, Mitsubishi, Nissan, Subaru, Suzuki and Toyota models. If one or more sensors have been replaced, the new ID information has to be input directly into the system. So if you don’t have a TPMS tool that can do this, your only alternative is to send your customer back to the new car dealer to have the ID reprogramming done.
 
TPMS relearn procedures vary a great deal from one vehicle to the next, so you also need access to the TPMS service data for the vehicle, or a reference manual or chart that covers the relearn procedures. Without this vital information, you can’t reset the system.
 
Essentially, most relearn procedures require you to put the system into a relearn mode. On some, this may require a command from a scan tool or plug-in TPMS tool. Or, you may have to cycle the ignition key on and off a certain number of times while stepping on the brake pedal. On others, the keyless entry fob may be used to wake up the TPMS module and ready it for relearning.
 
When the TPMS is ready, it may signal by beeping the horn or flashing the hazard lights. The TPMS activation tool is then placed near one of the tire pressure sensors, and a button is pressed for five or six seconds to wake up the sensor. As soon as the TPMS module recognizes the sensor and learns its position, the system signals again by beeping the horn or flashing the hazard lights. You then repeat the same procedure for each of the remaining tire pressure sensors in the specified order until the relearn procedure is complete.
 
Even on vehicles that have a key fob or driver information center relearn procedures, scan or dedicated TPMS tools that can interface through the OBD II connection can have advantages when it becomes to difficult to reprogram vehicles. 
 
With some procedures using a J-41760 magnetic tool, you are flying blind. Problems with the key fob, antenna and even the module or serial data bus connection can leave you chasing your tail. With a scan or dedicated scan tool, it is possible to perform a more accurate relearn and diagnosis and problems.  

You May Also Like

The Winter Tire Opportunity – Now Is The Time

Winters tires aren’t just a luxury, it’s your job to tell your customers the positive impact that the tires can give them.

It was a frigid February morning in Chicago last year. The kind of cold that creeps into the depths of your lungs, making it difficult and even a little painful to breathe. The kind of cold that literally takes your breath away. The snow was falling as I stepped into my car and took off across The Chicago Skyway with the city lights in my rear view. It was around Gary, Indiana, that the lake effect snow engulfed Interstate 90 and made it impossible to see the road more than about 15 feet ahead as I made an unwise attempt to pass a massive snowplow in the right lane. And, it was this moment that I understood the difference between an all-season tire and a true winter tire. My life as a “tire guy” would never be the same again.

Diagnosing Audi A8 TPMS Issues

These are all the steps you’ll need to pinpoint fault issues in TPMS for 2009-2016 Audi A8 vehicles.

The Rule of 3X Tire Rotation

Proper rotation procedures maximize tread life and customers coming back.

Communicating The Effectiveness Of TPMS

A good angle to start with may be laying out the consequences of not having a working TPMS.

Servicing Tires With 18-In.-Plus Rims

Servicing any tire and wheel assembly correctly starts with having the right equipment.

Other Posts

ATEQ TPMS Tools Adds Tesla BLE Function To VT67

ATEQ’s new VT67 TPMS Tablet will be capable of reading and programming the Tesla BLE sensor.

TPMS Valve Stems – What Are The Trends? What Is The Future?

Whatever the type of stem, carelessness can result in a broken sensor or even a customer being stranded with a flat tire.

Nissan TPMS Service

The behavior of the TPMS systems is very consistent across all Nissan models.

TPMS Sensor Signals

TPMS sensor signals are low power and low frequency, with most sensors transmitting at 315MHz or 433MHz.