Preventive Maintenance Tips To Avoid Coolant Hose Failure

Preventive Maintenance Tips To Avoid Coolant Hose Failure

Determining a worn-out hose isn’t as simple as it used to be. This video is presented by The Group Training Academy.

Today’s complicated cooling system no longer just keep the engine cool – they must cool AND warm various complicated components under the hood, as well as other areas of the vehicle. To do so quickly and efficiently, today’s vehicles use ‘modular’ coolant hoses.

They’re called that because hoses contain modules that may include a branching tee in the hose, quick-connect, valve, drain, air-bleeder or sensors. All have fluid flowing through them and are critical to the proper operation of the cooling system. They can be significantly more costly than standard, molded coolant hoses – so how can you help your customers be prepared?

Many years ago, the average vehicle had only four or five hoses including the upper and lower radiator, heater inlet and return, and a water pump bypass hose. In some cases, the lower radiator hose had a wire insert to keep it from collapsing at high engine speeds. Vehicles built during the past several decades may have a dozen or more small inside-diameter coolant hoses that perform diverse duties, like heating the throttle plate assembly or warming up thermostatic idle speed controls.

Determining a worn-out hose just isn’t as simple as it used to be. Typical rubber hoses generally wear from the inside out. You used to be able to do a simple “squeeze test” to check for a failing hose but now that’s a challenging chore, even with the hose removed from the vehicle.  

Most often, hoses fail because the coolant carries an electrical charge from component to component. The hose, liquid coolant and the engine/radiator fittings form a galvanic cell or “battery.” Called electrochemical degradation, or ECD, this chemical reaction causes micro-cracks in the hose tube, allowing the coolant to attack and weaken the hose reinforcement. Failures result from internal striations or cracks in the hose rubber, leading to pinhole leaks or a burst hose. Gates hoses, for example, have been specially designed to be “ECR” or Electro-Chemical Resistant.

Other factors can damage hoses as well. Fluids, including oil and other petroleum-based products, attack the rubber compounds and softens the hose either externally or internally through contaminated coolant. An oil-contaminated hose will feel spongy and bulges or swelling will be present. External oil leakage onto hoses should be corrected immediately and the hoses should be replaced. If a petroleum product contaminant is found within the cooling system such as from a failed head gasket, it too should be repaired, and all coolant hoses replaced.

Don’t forget to check for heat and abrasion as well. Look at where the hoses are routed and protect the hose from heat sources, sharp objects and even original metal cradles that came with the vehicle from the manufacturer.

While standard, molded EPDM hoses typically fail around the 95,000-mile mark, modular hoses typically fail much earlier. The plastic utilized with the branching tees, quick-connects and other components are affected by the same conditions as the hose, particularly from heat, and will become brittle over time.

Coolant hose failures can lead to anything from a driver being stranded on the roadside to a significant and costly engine overhaul. Replacing these complicated components with the best products will keep your customers safe. Do them a favor by explaining why preventive maintenance is in their best interest.

Visit Gates Corporation for more customer service information.

This video is sponsored by The Group Training Academy.

You May Also Like

Performing a Corner Check

Performing a corner check to inspect the condition of the steering, suspension and drivetrain components should be part of your normal routine. This video is sponsored by GSP North America.

Vehicle inspections are part of our everyday routine. Our customers rely on us to make sure their cars are safe and enjoyable to drive, but they don't know them as well as we do. They may not recognize problems that develop slowly with age and mileage. The safety of a vehicle relies on the condition of the suspension, steering and drivetrain to ensure not only the tires remain in constant contact with the road, but that the proper alignment angles are maintained during the full range of suspension travel. This includes the shocks and struts, as well as control arms, steering knuckles, ball joints, tie rods, wheel bearings, and CV drive axles. All these components are interrelated and only when they all perform correctly will all vehicle suspension handling, braking, and traction control systems work as designed. Performing a corner check to inspect the condition of the steering, suspension and drivetrain components should be part of your normal routine.

Understanding and Preventing Brake Noise

Silence noise with a complete brake job. This video is part of the Group Training Academy.

Charging for Diagnostic Time

Diagnostic work is more sophisticated and your techs’ time is worth charging for. This video is sponsored by Auto Value and Bumper to Bumper.

Understanding Stretch Shrink Belts

Andrew Markel uses an old school toy to describe how these belts work. This video is sponsored by Auto Value and Bumper to Bumper.

Mass Air Flow Sensor Cleaners

What can you do both for maintenance and for service and diagnostics to confirm a mass airflow sensors functioning properly? Andrew Markel shares the secret in this video sponsored by Auto Value and Bumper to Bumper.

Other Posts

ADAS Calibrations: Limited Space

Babcox Media’s Joe Keene provides a quick overview of many examples that demonstrate ADAS work should be in play for almost everyone.

Vacuum Pumps and Parking Brake Actuators

As the car parc evolves, so do service opportunities. This video is sponsored by Standard.

Gasoline Direct Injection Technology

Gasoline Direct Injection technology has been a key part of improving fuel economy and reducing emissions since the early 2000s. This video is sponsored by Standard.

Software Focus: Efficient Diagnostics

Discover how to quickly retrieve codes, access exclusive repair information, and develop a strategic plan for optimal diagnostic results. This video is sponsored by Bosch.