Power Steering Hoses: Inspection And Repair

Power Steering Hoses: Inspection And Repair

As part of any power steering inspection, first look at the fluid. If the fluid is grey or black, it could be a sign the inner layers of the hose have been compromised by worn, degraded or incorrect fluid. This type of discoloration is caused by rubber or metal particles in the fluid.

What Causes Power Steering Hoses to Fail?

The life of power steering hoses is not easy. Power steering hoses must endure some of the highest pressures and temperatures under the hood. Coupled with ozone, oil and solvents attacking the outer layers of these power steering hoses, it is easy to see why some hoses fail.

Power steering fluid is very flammable. When it ignites, it is very difficult to extinguish. Also, loss of power steering can cause an accident. Inspection of the lines is very important and any leak should not be taken lightly

Power Steering Hoses: Start at the Reservoir

As part of any power steering inspection, first look at the fluid. If the fluid is grey or black, it could be a sign the inner layers of the hose have been compromised by worn, degraded or incorrect fluid. This type of discoloration is caused by rubber or metal particles in the fluid.

Power Steering Pump

High-temperature pulsations cause power steering hoses to deteriorate from the inside. The constant flexing and pressure surges result in the breaking off of small particles of hose, which are carried through the system and can lead to system malfunction.

When performing an inspection of power steering hoses, any imperfection on the outside should be carefully inspected for the following signs:

Abrasion: If the outer layers of power steering hoses show any physical damage, they should be carefully inspected. If the outer layers are damaged, the inner layers of the hose could be exposed to damaging chemicals, heat and ozone. If there is damage to the power steering hose, investigate how it was damaged. Worn motor mounts, missing mounting tabs and exhaust gasket leaks can damage power steering hoses.

Bulges: Any bulges on power steering hoses are a sign that the internal layers have failed, fluid is working between the layers, and complete failure is imminent.

Softness: If a hose feels soft in an area, it is a sign that the internal or external layers are breaking down.

Cracking and Flaking: If a power steering hose’s outer layer is cracking or flaking, it is an early sign of internal wear, and the hose has lost its ability to absorb pressure surges.

Corrosion: Extreme corrosion on the fittings can cause the power steering hose assembly to fail. Most fittings are covered with corrosion-resistant coatings and plating methods. If they are removed due to abrasion, solvents or other processes, the fitting will eventually fail.

Leaks: Power steering fluid does not magically disappear. Any leak in a hose assembly is a problem that should be addressed.

Power Steering Hoses

Types of Power Steering Hoses

There are two general categories with power steering hoses: high- and low-pressure. High-pressure power steering hoses can have as many as five layers to handle up to 1,500 psi. The inner layers are resistant to the fluid and seal it against permeation into the outer layers.

The next inner layer is designed to give the hose strength against high pressure. These layers can be made of high-tech polymer materials and fabrics. The outer layer of these power steering hoses is designed to protect the inner layers against abrasion, chemicals and heat.

Low-pressure power steering hoses are designed with fewer layers and made to withstand less pressure. But, they must have the same resistance to elements found in the engine bay.

High-pressure power steering hose assemblies should use a hose that meets or exceeds SAE J2050. This standard test puts not only the power steering hoses, but also the fittings to a torture test ranging from 40 to 150 °C (-40 to 302 °F) and 1,500 psi maximum working pressure. Low-pressure/return hoses should be of the SAE J189 or J188 variety. This type of hose has to endure the same temperature range as the SAE 2050 hose, but only is tested to 250 psi.

It is highly recommended if a high-pressure hose is replaced, the low-pressure hose also be replaced.

 

 

 

You May Also Like

Ride Height Sensors

If one of these sensors is replaced, it must be calibrated after it is installed.

Ride-height sensors not only measure the position of the suspension, but also the rate of movement. They are supplied with a voltage of around 5 volts. The signal voltage is changed as a magnet moves past a coil. Most sensors have three wires — ground, power and signal.

Internally, it is difficult to damage one of these sensors. Externally, the linkage that connects the sensor to the suspension arm can also be damaged. The connector can be damaged and cause a short or open and a code will be set. If one of these sensors is replaced, it must be calibrated after it is installed.

GM Rattle or Creak Noise From Front Suspension

The noise may be originating from the front lower control arm front bushing. Here’s how to correct it.

Mercedes Airmatic Suspensions

Diagnostic tips to aid your repair efforts.

The Complete Shock And Strut Swap

One mistake to avoid when replacing struts is reusing the bearing plates or upper mounts.

ADAS Sensor Corrections

When performing a calibration, you are adjusting the connection between the sensor, vehicle and surroundings.

Other Posts

Struts and Memory Steer

We can summarize the cause of memory steer in one word: binding.

Reprogramming ADAS Procedures

As a vehicle ages, the J2534 programming becomes even more important to the vehicle’s ADAS operation.

Air Ride Conversion Kits

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring.

Curing Shock, Strut and Suspension Noise

As vehicles age, eliminating noise is Job 1. But ‘noise’ may mean different things to you and your customers.