Nissan Tech Tip: Diagnosing an Altima Engine Misfire

Nissan Tech Tip: Diagnosing an Altima Engine Misfire

The engine runs rough, gas mileage is down and more importantly the "check engine" light is on. That little illuminated check engine light strikes fear in the hearts and minds of the average vehicle owner - it's supposed to. Otherwise, people would keep driving their vehicles as long as they could, eclipsing the light with a piece of electrical tape.

The engine runs rough, gas mileage is down and more importantly the "check engine" light is on. That little illuminated check engine light strikes fear in the hearts and minds of the average vehicle owner – it’s supposed to. Otherwise, people would keep driving their vehicles as long as they could, eclipsing the light with a piece of electrical tape. That wouldn’t be good for our air quality. Luckily, most good citizens are of the belief that if that check engine light is on, not only is the vehicle going to leave them stranded at the most inopportune time, a plague could befall their entire family and their subsequent heirs for generations.

To the professional technician however, the "check engine" light is a sign that there may be a significant problem, but it’s probably nothing that’s going to change the course of history. With the help of ongoing education, a good scan tool and accurate diagnostic information, thousands of technicians repair "check engine" light related problems daily.

So why does something as simple as an engine misfire warrant a tech tip? Many techs assume that because automotive technology has become more complex, drivability problems have become more complex. In some ways they have, but on the other hand, sometimes facilitating a timely repair is just a matter of checking the simple basics.

In keeping with the simplicity theme, let’s cut straight to the details of this tech tip. If any of the applied vehicles (listed below) have a check engine light on, diagnostic trouble codes P0300 through P0304 (cylinder misfire) stored and/or exhibit a rough running engine, check the spark plug wire tubes and boots as follows:

Applied Vehicles:
• 1995-97.5 Altima (U13) models built before: 1N4BU31D3VC245368; and
• 1998 Altima (L30) models built before: 1N4DL01D8WC165916.

Applied Dates:
• 1995-97.5 Altima (U13) models built before March 5, 1997; and
• 1998 Altima (L30) models built before October 28, 1997.

PROCEDURE:
1. Remove the spark plug wires and inspect for water in the spark plug holes.

If water is in the spark plug holes, perform the following steps:
• Remove water from the spark plug holes.
• Insert a paper clip through the steam vent hole in the spark plug wire boots to insure the holes are clear (see Figure 1).

NOTE: The steam vent hole allows water vapor to escape if water becomes trapped in the spark plug hole.

• Inspect spark plug wire boots for cracks, hardening or deformities that could prevent sealing between the boots and the camshaft (valve) cover.
• Replace all spark plug wires if one or more of the boots show signs of cracks, hardening or deformities.

If the spark plug holes are dry and the spark plug wire boots are in good condition, proceed with step 2.

2. Inspect the entire surface of each spark plug wire tube for pinholes and/or cracks (see Figure 2).

• If one or more spark plug wire tubes have pinholes and/or cracks, replace all of the spark plug wires.

And there you have it — in these complex times, a simple solution to a simple problem. And all that was required was an ongoing education, a good scan tool and accurate diagnostic information. It’s up to you to provide the first two items. As for the last item — I’m always glad to help.

Written by ALLDATA Technical Editor, Rich Diegle. Rich is an Advanced Engine Performance Certified and ASE Master Technician with an Associate of Arts degree in automotive technology and 22 years of dealership and independent shop experience.

For additional information, visit www.alldata.com.

You May Also Like

Service Opportunities Still Exist With EVs

Like all ICE vehicles, you need the correct tools, parts and to follow the proper service procedures when servicing EVs. This video is sponsored by The Group Training Academy.

According to a recent survey of shop owners, less than a third of shops work on EVs, due to concerns about battery packs, inverters or other daunting technology. The good news is, though, tomorrow’s electric and hybrid vehicles still offer substantial service opportunities under the car.

Just as with conventional internal combustion engine or ICE vehicles, EVs are subject to the same traffic conditions, potholes, curbs and corrosive environments that can accelerate wear and tear on steering and suspension components. But there are also several other factors with EVs that can make life harder for the suspension.

Do Technicians Need Tips?

Asking for a tip would not go over well with your future customers.

Wheel Bearing Shortcuts

When you’re installing a wheel speed sensor on a hub unit, never ever remove it from the original unit. Sponsored by Auto Value and Bumper to Bumper.

Green Li-ion Launches Lithium-Ion Battery Materials Plant

The plant is North America’s first commercial-scale plant to produce recycled lithium-ion engineered battery materials.

FCS Introduces 16 New Numbers

The new numbers cover some of the most popular applications on the road today, including the Jeep Compass, Lexus GX470, Mazda 3 and more.

Other Posts

Maverick Tire Changer: Handling Large Custom Wheels

Large, custom 4×4 wheels are all the rage, and Hunter’s Maverick tire changer makes handling them a breeze.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.

Introduction to the Maverick Tire Changer

Joe Keene speaks with Hunter Engineering service rep Rick Marzen on Hunter’s premium center-clamp Maverick tire changer.

Autel Energy Europe Releases MaxiCharger Launch Plan

Autel released the MaxiCharger Megawatt Charging System satellite launch plan at the Nordic EV Summit 2024.