Low Sinking Or Spongy Brake Pedal

Low Sinking Or Spongy Brake Pedal

When diagnosing a master cylinder, keep in mind the type of seals that are used are lip cup seals. This design allows for the seal to improve as the pressure increases. Another feature of this seal is that it does not create a vacuum when the piston retracts.

Condition

Master cylinder may be leaking fluid past the piston seals internally (by passing), not building up pressure.

Master cylinder pistons with lip cup seals
Master cylinder piston with lip cup seal

Repair Procedure

When diagnosing a master cylinder, keep in mind the type of seals that are used are lip cup seals. This design allows for the seal to improve as the pressure increases. Another feature of this seal is that it does not create a vacuum when the piston retracts.

As the pedal is depressed, the piston is pushed in the forward direction. The lip cup seal, attached to the primary piston, builds pressure up in the primary chamber first, which in turn forces the secondary piston forward, building pressure in the secondary chamber. As the pressure increases in both chambers, the edges of the seal are pressed against the bore of the master cylinder. The higher the pressure, the better they seal.

In the manufacturing process, the testing procedure for master cylinders is done at low pressure. Lip cup seals are more likely to fail under low pressure.

 

When the piston is released, fluid in the primary chamber flows between the reservoir and the bore of the cylinder.
When the piston is released, fluid in the primary chamber flows between the reservoir and the bore of the cylinder.

When diagnosing the automobile hydraulic system, the first thing to do is perform an isolation test. Use the proper tool and clamp off all the hydraulic brake hoses.

Press down on the brake pedal. If the pedal is low or spongy, remove the brake lines from the master cylinder and install plugs in the outlets.

Press down on the brake pedal. Release the pedal and wait approximately 10 seconds. This allows the quick take-up valve to open and the air to escape through the master cylinder compensating port and the fluid in the reservoir to enter the bore of the master cylinder. Once air stops coming up into the reservoir, or the pedal becomes firm, apply light pressure to the pedal and observe if the pedal continues toward the floor.

When the master cylinder ports are plugged, and the air is bled out of the bore, the pedal should be high and hard under low pedal effort or high pedal effort. If the pedal sinks under either condition, the seal is damaged and the master cylinder should be replaced.

Courtesy of Raybestos Brakes

You May Also Like

Randy Breaux, Group President, GPC North America, Talks to AMN Drivetime

At NAPA, “Breaux Knows” business relationships, ABCs to avoid, and serving the automotive professional.

Growing up in South Louisiana, Randy Breaux started working young, inspired by his machinist father and grandfather. His formal career began after college, spending 26 years in manufacturing, with 21 of those at Baldor Electric Company. Following its acquisition by a European firm in 2011, he transitioned to the distribution side, joining Motion, a division of Genuine Parts Company.

Is Training For The Sake Of Training Always Worth It?

Technology changes every day. Are you keeping your techs in top shape?

Understanding Customer Clunking And Clicking Complaints

Can Your Techs Diagnose and Repair Modern Axle Complaints?

Comprehensive Guide to Serpentine Belt and Drive System Maintenance

Properly maintaining the entire drive system prevents premature belt wear and system failure, ensuring customer satisfaction and vehicle reliability.

How Modern Car Sensors Optimize Performance and Emissions

Learn how Standard ensures accuracy, speed, and durability in their sensors to maximize engine performance and efficiency.

Other Posts

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

Top 10 Wheel Bearing Torque Tips

A torque wrench is an essential tool when it comes to installing wheel bearings.

Blink CEO to Present at Energy, Power & Renewables Conference

The event is scheduled for June 17 at 1:10 p.m. ET.

Tool Time Podcast: Lumileds

Nadine and Eric sit down with Lumileds’ Aubry Baugh to discuss all the professional lighting solutions the company has to offer.