Connect with us
2015 GMC Canyon Automatic Locking Rear Differential

Chassis

Live-Axle Wheel Bearing Replacement

Replacing rear wheel bearings on a live-axle rear suspension requires a few extra steps when compared to a unitized bearing. To remove the axle shaft, the differential must be accessed and the clips that hold the axle in the differential must be removed.

Advertisement

2015 GMC Canyon Automatic Locking Rear Differential

Advertisement
Click Here to Read More
Advertisement

Replacing wheel bearings on a vehicle with a live rear axle may not be one of the most frequent jobs, but it can be one of the most profitable. While the basics have not changed in more than 60 years, new seal materials and differential designs have added new wrinkles.

Bearings

Replacing rear wheel bearings on a live-axle rear suspension requires a few extra steps when compared to a unitized bearing. To remove the axle shaft, the differential must be accessed and the clips that hold the axle in the differential must be removed.

There are three bearing styles — Conrad, roller and ball. Most axles use these types of bearings in a cartridge-type arrangement. They are installed into the axle ends or pressed onto the shaft and possibly held in place with a pressed-on retainer. On some axles, the bore on the housing is tapered and the bearing will fit in only one direction. This is where measuring tools can save you time and maybe multiple part deliveries.

Some axles use a “floating” axle shaft design. This design takes the weight of the vehicle off the axle so all it has to do is transmit power. This allows the hub of the axle to carry a greater load. Some of these axles use tapered roller bearings. Another advantage of a floating axle is if the axle separates from the differential or flange, the wheel will not fall off the axle.

Advertisement

The most critical part of the disassembly is removing the bearing and retainer from the shaft without damaging the axle shaft or housing. Any damage to the surfaces that the seal or bearing rides on can cause a premature failure of the new bearing.

Another rookie mistake made by some technicians is installing the parts in the wrong order. It is not uncommon to press the new bearing onto the axle only to realize the flange plate was not installed.

Look at the differential cover before you quote the job. On snow-belt vehicles, the differential cover is prone to rust. Perforation does happen, but chances are prying on the weakened cover may distort it to the point that it will never seal. Replacement covers are readily available and very economical.

Seals

The main killer of solid axle wheel bearings is a failed seal. Most seals ride on the axle shaft, and they typically have a lip and a spring that holds the lip to the axle. When a seal is installed, take your time installing the axle. Splines can damage the seal and cause leaks.

The area on the axle shaft where the seal and bearings make contact is the most important. It must be free of rust and imperfections. Use only a fine-grade emery paper to clean the axle shaft between the flange and the worn area.

Advertisement

If the surface is grooved or damaged, the axle can be repaired with a sleeve on some applications. If not, the axle should be replaced. Another option for some applications is to install a replacement bearing that repositions the bearing and seal to ride on unworn surfaces.

Make sure the seal is installed in the correct position. A correctly installed bearing may extend out from the housing up to 1/4”. Some axles have small seals that must be positioned properly so pressures can be relieved and the lip can work.

Make sure the breathers on the axle are not clogged. The breather on some axles acts as a PCV valve to keep pressures within a certain range so the seals can work their best as the differential heats and cools. If a breather is clogged, the heat will increase pressure in the axle. As the axle cools, a negative pressure could build up behind the seal. These changes in pressure will cause the lips of the seals to deform and leak.

Any leak on an axle should be taken seriously. Ignoring a leak can be very expensive and destroy the bearings, brakes and differential.

Advertisement
Click to comment

Strut Service Q&A

Variable Ratio Steering Systems

How To Install Struts

Power Steering Service Tips

Advertisement

POPULAR POSTS

Sponsored Content

A guide to replacing a wheel hub flange and bearing

Sponsored Content

Benefits of Using OE-Quality Parts: Part 1

Sponsored Content

Understanding Misfire Codes And Ignition Coils

Sponsored Content

Benefits of Using OE-Quality Parts: Part 2

Connect