Kia Tech Tip: TCM Logic Revision

Kia Tech Tip: TCM Logic Revision

This bulletin provides information related to a logic change in the Transmission Control Module (TCM) for 2001 Rios, and 1998 through 2001 Sephia and Spectra vehicles built after Oct. 18, 2000.

This bulletin provides information related to a logic change in the Transmission Control Module (TCM) for 2001 Rios, and 1998 through 2001 Sephia and Spectra vehicles built after Oct. 18, 2000. On vehicles built before that date, under certain driving conditions the following DTCs may be stored without a true defect being present: P0705, P0740, P0731, P0732, P0733 and P0734.

TCMs in vehicles built after Oct. 18, 2000 use a revised diagnostic routine software to reduce the incidence of related DTCs. The revised TCM should be used to repair affected vehicles experiencing a repeat incidence of the above-mentioned DTCs.
Note: The part number for the revised TCMs did not change. However, all TCMs currently in PDC stock have the revised logic.

Preliminary:
• Familiarize yourself with the procedures outlined in TSB, Transmission/Driveline 003. Obtain an A/T diagnosis worksheet and fill it out as you proceed.

• Check the A/T fluid for level and appearance. If the fluid is burnt or contaminated, the transaxle may have to be replaced per the instructions in the TSB before proceeding.

• Check for any (pending) DTCs, record their description and freeze-frame data. If any electrical or circuit related DTCs are stored, repair them before replacing the TCM or before attempting to correct DTCs that indicate system malfunctions.

• On repeat repairs, always check the vehicle’s repair history to determine previous repairs and whether they were effective. Use the repair history as required to aid in your diagnosis and repair procedures.

Inspection:

  1. Open the driver’s door and check the production date on the FMVSS door label.
  2. If the vehicle’s production date is Oct. 18, 2000, or later, the vehicle already has the correct TCM; no TCM replacement is required. Note: If the TCM has previously been replaced on this vehicle, it’s possible that an older version was inadvertently installed. When in doubt, check the TCM version regardless of the vehicle production date.
  3. If the vehicle’s production date is before Oct. 18, 2000, determine if the correct TCM version has been used.
  4. If the TCM is found to be an early version, proceed with step 5. Note: If the TCM is the correct version, and DTCs are stored, follow the appropriate procedures using DTC-specific checklists in the service manual and/or DTC-specific tips/information in the scan tool.

Repair Procedure:

  1. Make sure the ignition switch is off and the gear selector is in the “park” position.
  2. Locate the TCM under the left lower dash area.
  3. Rio only: Loosen and remove the three mounting nuts that secure the ECM mounting bracket to the firewall (these are also used to secure the TCM).
  4. Rio only: Loosen and remove the one remaining nut that secures the TCM mounting bracket to the firewall.
  5. Sephia/Spectra: Loosen and remove the two nuts that secure the TCM mounting bracket to the firewall.
  6. Remove the TCM, release the wire harness connector locking lever, then disconnect the TCM from the wire harness. Discard the old TCM.
  7. Install the new TCM in the reverse order of removal.
  8. Test-drive the vehicle after warm-up and check for (pending) DTCs. If any (pending) DTCs set during the test-drive, investigate them and correct as required. Use flight record data and follow the appropriate procedures using DTC-specific checklists in the service manual and/or DTC-specific tips/information in the scan tool.

Courtesy of IDENTIFIX.

For additional information, visit www.identifix.com.

You May Also Like

Is Training For The Sake Of Training Always Worth It?

Technology changes every day. Are you keeping your techs in top shape?

We all know the value of training - or do we? Is it always valuable? Is it alway effective? Should it always take top priority?

Naturally, you want to say yes, but experts say the RIGHT training for your team's needs is what's really crucial.

This episode of Talking Shop with ShopOwner focuses on the challenges of training technicians and service advisors in the automotive industry. The guests, Dave Boyes and Ron Shanas from Today's Class, discuss the importance of training in a rapidly changing technological landscape and the difficulties shop owners face in finding time for training amidst busy schedules.

Understanding Customer Clunking And Clicking Complaints

Can Your Techs Diagnose and Repair Modern Axle Complaints?

Comprehensive Guide to Serpentine Belt and Drive System Maintenance

Properly maintaining the entire drive system prevents premature belt wear and system failure, ensuring customer satisfaction and vehicle reliability.

How Modern Car Sensors Optimize Performance and Emissions

Learn how Standard ensures accuracy, speed, and durability in their sensors to maximize engine performance and efficiency.

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

Other Posts

Top 10 Wheel Bearing Torque Tips

A torque wrench is an essential tool when it comes to installing wheel bearings.

Blink CEO to Present at Energy, Power & Renewables Conference

The event is scheduled for June 17 at 1:10 p.m. ET.

Tool Time Podcast: Lumileds

Nadine and Eric sit down with Lumileds’ Aubry Baugh to discuss all the professional lighting solutions the company has to offer.

Charging More May Bring Customers Back

Here’s why charging more for brake jobs keeps customers coming back.