Jeep Tech Tip: Squeak-Like Sound from Front Bumper Crossmember

Jeep Tech Tip: Squeak-Like Sound from Front Bumper Crossmember

A customer may experience a squeak-like sound when driving slowly over driveway entrances, road bumps or when performing parking lot maneuvers. The squeak-like sound may occur when the vehicle body/frame is flexed (twists). This condition may occur when the front edge flange of either frame rail rubs against the backside of the front bumper crossmember.

Vehicles: 2002 Jeep Liberty and Cherokee models.

Symptom/Condition:
A customer may experience a squeak-like sound when driving slowly over driveway entrances, road bumps or when performing parking lot maneuvers. The squeak-like sound may occur when the vehicle body/frame is flexed (twists). This condition may occur when the front edge flange of either frame rail rubs against the backside of the front bumper crossmember.

Diagnosis:
With the vehicle stopped and in park, slowly rock the vehicle from side-to-side. Applying force to the top edge of the driver or front passenger side door opening may be of assistance. If present, the squeak-like sound will come from behind the front bumper fascia and in the immediate area below either front headlamp.

Another diagnostic method is to set the parking brake, start the vehicle engine, and while in park, slowly turn the vehicle front wheels from side-to-side (to flex the body) while someone listens at the front of the vehicle.

If the above condition is present, perform the Repair Procedure to both the left and right side of the front bumper crossmember.

Repair Procedure:

  1. Remove the vehicle front grill and fascia. For additional disassembly and assembly instructions, refer to the Frame & Bumper section of the appropriate 2002 service manual.
  2. Remove the screw used to secure the right side frame rail end cap to the front bumper crossmember. The frame rail cap covers the rectangular access hole in the crossmember. Remove the end cap.
  3. 1 – Right Side Frame Rail
    2 – Weld Lines – already present
    3 – Front Bumper Crossmember
    4 – Mark line as specified, clamp panels, center punch, drill 3/16 in. holes, add rivets
    5 – Draw vertical line 9 mm from inboard edge of rectangular access hole.
    5 – Five (5) spot welds – already present.

    Draw a verticle line from the top to bottom across the width of the front crossmember. The vertical line should be positioned so that it is 9 mm to the right, and parallel to the inboard vertical edge of the right access hole (in the crossmember). See illustration in Figure 1.

  4. Mark the vertical line in three places as illustrated. Each top and bottom mark is to be 20 mm (.750 in.) from the top and bottom edge of the crossmemver respectively. The middle mark is to be centered at 50 mm (2.0 in.) from the top and bottom edge of the crossmember.
  5. Center punch all three marks to prevent drill bit drift and improperly positioned holes.
  6. Position locking pliers through the rectangular hole in the crossmember. Tightly clamp the crossmember panel to the frame rail edge flange. Position the locking pliers so that they will not interfere with the drilling of the three holes or with the heads of the rivets when they are installed.
  7. Using a 3/16 size drill bit, drill a hole at each of the three marks made on the vertical line. Drill all the way through both metal panels (the crossmember and frame rail edge flange).
  8. Make sure the area around the three drilled holes is free of metal burrs. Install a suitable corrosion-resistant material (e.g. paint primer) to the drilled holes.
  9. With the two panels securely held together by the locking pliers, install a rivet (p/n 34201208) in each drilled hole.
  10. Remove the locking pliers.
  11. Move to the rectangular access hole located at the left side (driver side) of the front bumper crossmember.
  12. Perform steps 2 through 10 in a similar manner so that the installed rivets are positioned along the inboard edge of the driver-side rectangular access hole. The left side repair should mirror the repairs made to the right side.
  13. Verify that the squeak-like sound condition has been corrected.
  14. Install both end caps and screws.
  15. Install the front fascia and grill.

For additional information, visit www.mitchell1.com.

Technical service bulletin courtesy of Mitchell 1.

You May Also Like

Non-Competes

The FTC’s rule is set to take effect in about four months, unless it is blocked by legal challenges.

A Non-Starter, Says FTC

As you read ShopOwner, whether it is in print or online, one thing – hopefully – comes across clearly: our mission is to help your shop be more successful.

Sometimes, that is evident through solid marketing advice, updated technical resources or inspirational messages about other successful shop owners who deal with challenges in creative ways. Typically, each issue of our magazine contains all three – and then some.

Eaton Introduces Fuse Portfolio for Electrified CVs

Eaton Bussmann series fuses can handle up to 1,400 amps and 900 volts, and can be tailored to customer specifications.

Succession Planning – Navigating The Legal Landscape

Planning for a successful business handover means doing things by the book.

Genesis Expands EV Availability to 37 States

GV60, Electrified GV70 and Electrified G80 are now available at select retailers in Alabama, Kansas, Oregon and Rhode Island.

Driveshaft, Axle and Drivetrain Noise FAQs

Follow along to learn more about these unwanted noises.

Other Posts

Non-Directional Rotor Finishes

Today, non-directional finishes on new brake rotors still serve the same purpose, but they also help in the bedding of some friction formulations.

PRT Launches 59 New Complete Strut Assemblies

Extending PRT’s product portfolio in North America, the new release represents nearly 12M vehicles in new coverage.

We Want Your Thoughts On Electronic Power Steering

Your opinion matters us and can be profitable for you too! Share your ideas with us.

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.