Diagnosing Catalytic Converter Problems (Video)

Diagnosing Catalytic Converter Problems (Video)

There are multiple steps to diagnosing a possible air related issued on a catalytic converter. Sponsored by AP Emissions.

CC: In our previous videos we talked about how catalytic converters work, what triggers a catalyst inefficiency code, what causes thermal damage, and catalyst poisoning and how those problems reduce the efficiency of our catalytic converter.  In this video we will discuss some diagnostic procedures for catalytic converter problems arising from issues relating to air, in our air, fuel and, spark conceptual grouping

Our first step is to do a visual inspection for worn out gaskets and vacuum leaks. Do a smoke or soap bubble test if you suspect vacuum leak but cant find it

Check your mass air flow sensor and clean or replace as needed (use a scan tool or multimeter to note quick increase from 2-7 grams per second at idle to 15-25 g/s at 2500 RPM)

Test and replace any lazy upstream oxygen or “Air/Fuel” sensors– a recent CARB emissions roadside emissions check found that half of all converter failures were due to a lazy upstream sensor.

  • Check upstream O2/AF sensor is not lazy, weak, or fouled.
  • Voltage should rise to 850 mV
  • Voltage should drop to 150mV
  • Never drop below 0
  • Voltage should switch once every 2 seconds to 5 times per second
  • Voltage rise time less than 80 ms
  • Voltage fall time should be less than 100 ms

Check upstream AF sensor

  • Add metered propane, or something highly combustible like brake cleaner into air intake to force it rich, or force a lean condition with vacuum leak downstream from MAF. In both cases you should see the sensor respond very quickly. If a sensor is lazy, it should be replaced immediately.
  • 02 and Air fuel sensors should be replaced as part of your regular maintenance and tune up schedule.

Look for and patch exhaust leaks. Common locations for exhaust leaks are near hangers, at gaskets and where two surfaces are welded together. Exhaust leaks can result in a lean air fuel mixture.

Check engine compression to make sure the pressure in combustion chamber is within spec and evenly balanced across cylinders.  

In our next video, we will be looking at catalytic converter diagnostic tips related to fuel.

This video is sponsored by AP Emissions Technologies.

You May Also Like

Limited Slip Supplement (VIDEO)

If the frictional properties are not correct, chatter will occur. Sponsored by Lubegard.

Welcome to the Lubegard Limited Slip Supplement overview. Clutch-based limited slip differentials are common on many automotive applications like trucks and SUVs, but they present a unique problem. These differentials often use different clutch configurations, either cone or flat type, made with various materials and frictional requirements. When both wheels have ample traction, the clutch plates bind together tightly, sending consistent power to each wheel. When one wheel slips, additional power is sent to the other wheel based on the frictional properties of the clutch packs. This is where the gear lubricants frictional properties play an important role in functionality and performance.

Rust and Corrosion Preventive Oil (VIDEO)

Your tools and equipment need to be protected from rust. This video is sponsored by Lubegard.

Auto Pros Team Visits Hybrid Shop of The Carolinas

Auto Pros on the Road puts the Babcox team into shops across the USA. This episode is sponsored by Autolite.

Nissan Around View ADAS Camera Calibration (VIDEO)

Always calibrate the around view monitor system after a collision.This video is sponsored by Hunter Engineering.

Collision Blueprinting with Alignment Equipment (VIDEO)

An alignment is usually called for prior to ADAS calibrations. This video is sponsored by Hunter Engineering.

Other Posts

AP Emissions Releases January New Part Number Update

The release includes direct fit EPA converters covering more than 6.6 million vehicles in operation.

Stainless Steel Did Not Kill The Exhaust Repair

Direct fit parts can be used to make an effective repair quickly.

Replacing Master Cylinders

The most common problems that occur in the master cylinder are wear in the piston bore and piston seal failure.

ADAS Suspension Alignments

Look at the “big picture” and really consider how the vehicle will operate if things aren’t done correctly.