Brake Hardware: Lessons Learned From a Little Piece of Wire

Brake Hardware: Lessons Learned From a Little Piece of Wire

Every technician has struggled with those little wire clips that push the pads onto the pistons on first-generation Mazda Miatas. Those little clips that barely fit into the painted-over holes on the new pads and can shoot across the shop like a rubber band can make a big difference.

One racecar builder who specializes building “showroom stock” vehicles found out just how important this small piece of brake hardware can be. This builder commonly discarded those little wire clips thinking that they did not provide any advantage in a racing environment.

While between runs on a chassis dyno he realized that the rear brakes of a vehicle needed new pads. Not having time to do the job himself, he had one of his employees perform the job. This time, the tech replaced the missing hardware including the wire clips that pushed the pads against the piston. On the baseline run, the car gained a very small amount of horsepower at the wheels.

The idea of gaining horsepower by replacing the brake hardware seemed impossible. But after he performed further runs with and without the clips, he realized that the little clips reduced brake drag.

The discovery meant more power at the track, but on the street it could mean a brake job that could last longer.

Hardware is for more than drums. Replacing disc brake hardware is critical to returning the system back to its original condition.

Brake hardware for disc brakes is not a dealer-only item. Your local jobber might carry three lines of hardware. This product category is more than shims, anti-rattle clips or dust shields. Many of these lines of products include items like caliper brackets, slides and all the soft parts to restore the system to like-new condition. Many of these parts are at reasonable prices that you and your customer cannot refuse.

SPRINGS AND CLIPS
Heating and cooling cycles can weaken springs and anti-rattle clips. Weak hardware parts can result in excessive caliper/pad movement or binding causing noise and other related problems. This can lead to uneven and premature pad wear, rotor warpage and pulling.

Some springs and clips can be difficult to install. Some anti-rattle clips may resemble Chinese finger traps when you are trying to reinstall them back on the car. But leaving them out is not an option.

When rust and corrosion build up on a floating caliper’s slides or bushings, it can prevent the caliper from centering itself over the rotor when the brakes are applied. Not only does this reduce effective braking force and increase the vehicle’s stopping distance, it also causes uneven pad wear.

The same condition may also create uneven braking between the right and left calipers, causing the brakes to pull toward the stronger side.

SOFT PARTS
When technicians think of brake hardware they think springs, clips and slides. But soft parts like dustshields, grommets and bushings need just as much attention.

Most floating brake calipers use a rubber or plastic insulator or shim around the mounting bolts of the caliper. This sleeve of soft material loses resiliency over its lifetime. This is hastened by the high-temperature environment of the brakes. As materials wear, instead of being round they are flattened by the torque from the brakes into an oval shape that can cause excessive caliper movement. This can cause noise like rattles and thumps even if the brakes are not applied.

Always inspect and replace if necessary any dust boots or grommets that protect caliper bolts or slides. If the soft parts look OK, clean out all the old lubricant and replace with new lubricant.

Unlike steel, soft parts like rubber are sensitive to chemicals. Choosing the right lubricant for these parts is critical to ensuring the integrity of the part.

There are three criteria to remember when selecting a brake lubricant. First, does it say that its a brake lubricant on the package? If not, do not use it. Some lubricants may say they are a silicone or molybdenum disulfide based, but they may not be formulated to work on brakes. Second, look at the effective temperature range of the lubricant. At minimum, a lubricant should be able to handle 400

You May Also Like

Non-Directional Rotor Finishes

Today, non-directional finishes on new brake rotors still serve the same purpose, but they also help in the bedding of some friction formulations.

Back in the day, a non-directional rotor finish was the method used to solve a common problem that occurred on bench brake lathes. If the crossfeed speed was too fast, the rotor became like a vinyl record, and the pads became the needle that followed the grooves in the record. This would cause a clicking noise as the pads moved in the caliper as it followed the concentric grooves.

Brake Problems

Reducing brake drag on late-model vehicles is not accomplished by a single component; it takes a system.

Wheel Bearing Service

When faced with any noise complaint, take the time to test-drive the car with the customer, if that’s possible.

Gen 1 Wheel Bearings

Removing and installing these bearings requires the correct tools and patience.

Tapered Wheel Bearings

Here’s what you should know as a technician when servicing tapered wheel bearings.

Other Posts
Do Severe Duty Brake Pads Trade Power For Longevity?

Accepting reduced component life for better braking power in severe-duty applications may be a thing of the past.

HELLA PAGID Launches Semi-Metallic Brake Pad Line

Global automotive brake systems supplier HELLA PAGID announced the launch of its latest product line of semi-metallic brake pads.

ShopOwner’s June Digital Magazine Available Now

This issue is free to download and read; priceless in business value.

Please Take Our Brakes/Rotating Electrical Survey

By entering, you’ll have a chance to win a $100 gift card or one of 10 $25 gift cards!