AWD Tire Rotations

AWD Tire Rotations

Intuitively, one would think that an AWD vehicle would not require regular tire rotations because power is constantly directed to all tires; therefore, all of the tires would wear at the same rate. That is the thought lingering in the minds of some AWD vehicle owners. But when it comes down to it, tire rotation is the second most important maintenance item (tire pressure being first) that can be performed to maximize tire life, and this also pertains to AWD vehicles.


Intuitively, one would think that an AWD vehicle would not require regular tire rotations because power is constantly directed to all tires; therefore, all of the tires would wear at the same rate. That is the thought lingering in the minds of some AWD vehicle owners. But when it comes down to it, tire rotation is the second most important maintenance item (tire pressure being first) that can be performed to maximize tire life, and this also pertains to AWD vehicles.

As far as tire wear goes, the mechanism that induces tire wear is slip. Think back to your high school physics class and the subject of friction. The force required to move an object along a surface equals the coefficient of friction multiplied by the load on the object.

Reaching this level of force, or wheel torque in this case, while driving usually results in wheel spin during acceleration or lock-up of a wheel under braking. Every time slip occurs, rubber molecules are sheared away from the tire tread and left on the roadway surface.

Slip also occurs as a vehicle turns a corner or changes direction. Tire engineers refer to the slip angle of a tire, which is the difference between the direction the tire is pointing and the actual path the tire takes.

As a side note, when the slip angle of the front tires is greater than the rear tires, then an understeer or push condition occurs. The opposite condition occurs, known as oversteer, when the slip angle of the rear tires is greater than the front tires. Most production road vehicles are designed to understeer because oversteer requires a bit more driver skill to correct and a majority of drivers do not have that specific skill set.

Focusing on tread wear, tire engineers manipulate the angles of the groove walls, or sides of the tread blocks, to control the amount of movement that the tread block experiences as it enters, rolls through and exits the footprint.

Perfect Balance and Rotation
Next, we add in vehicle alignment to the tread-wear recipe. Most automakers design vehicle suspensions with adjustable caster, camber and toe to achieve a desired level of handling and tread wear balance. The vehicle’s alignment specifications add complexity to the stresses on the tire tread, which can result in irregular wear as the vehicle rolls down the highway.

Considering that a vehicle’s weight distribution is generally 60% on the front axle and 40% on the rear axle, the reduced load on the rear tires can sometimes result in higher irregular wear because there is not enough weight to prevent straight-ahead rolling slip. An improper rear alignment will certainly guarantee irregular wear.

A regularly scheduled tire rotation is critical for long and even wear. Allowing each tire to run on every wheel position during the life of the tire will mix up the duty cycle for the tread pattern and prevent irregular wear patterns from setting in and reducing overall tread life. Irregular wear patterns also produce unnecessary and elevated tread noise.

A Forward-X rotation is recommended for front-wheel-drive vehicles, while the Rearward-X or X-rotation is best for rear-wheel-drive vehicles. This assumes that the front and rear tire sizes are the same.

For different sizes with non-directional tread patterns, rotation from side-to-side is the only option. Asymmetric tread patterns can be considered as non-directional. Front-to-rear rotation is applicable for directional tread patterns with the same size front and rear. A simple tire rotation does not apply to directional tread patterns with different front and rear sizes. The only option is to have the tires dismounted and remounted on the opposite side of the vehicle.

AWD Vehicle Considerations
A majority of AWD vehicles generally operate in two-wheel-drive mode and activate AWD based on demand. Wheel speed sensors detect a loss of traction and torque is directed to the wheel positions with better grip. The few exceptions in the market constantly split power between the front and rear axle, and also redirect power to the axle with the most traction. Some makers of these AWD systems may wrongly insist that one cannot use simple tire rotation patterns.

Regardless, each wheel position on an AWD platform sees varying degrees of driving traction and steering. Regular intervals of tire rotation between every 5,000 to 7,500 miles will maximize tire life and provide the best available traction and handling balance for the vehicle. If the drivetrain is primarily 2WD, then follow the rotation pattern that is correct for front- or rear-drive and the tread pattern.

You May Also Like

Diagnosing Active Roll Bars

Roll bars on modern vehicles are often a compromise between stability and comfort.

Roll bars, also known as sway bars or anti-roll bars, are responsible for controlling body roll when a vehicle goes around a turn. How do they do this? A roll bar is basically a long spring that connects both sides of the suspension across an axle. When a vehicle goes around a turn, the weight will transfer from one side to the other, compressing the outside suspension. The roll bar applies force to the inside suspension and reduces the amount the body can roll (Figure 1).

Mercedes Airmatic Suspensions

Diagnostic tips to aid your repair efforts.

Active Ride Control Diagnostics

The key to servicing these systems is proper information and understanding precisely how these systems operate.

Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.

Live Axle Wheel Bearing Service

Replacing rear wheel bearings on a live axle rear suspension requires a few extra steps when compared to a unitized bearing.

Other Posts

Simplifying AWD Systems

No matter the manufacturer, there is almost always an all-wheel drive (AWD) option for most platforms.

Multi-Link Front Suspensions

Why do some suspensions have so many ball joints?

How To Answer Customer Ride Control Questions

Presenting your customer with inspection results and benefits of replacement will help sell the job.

Finding Damaged Suspension Components

If camber is off on one side only, a close encounter with a pothole or curb may have bent a spindle, control arm or strut.