Alignment Specs: Thrust Angle and Setback

Alignment Specs: Thrust Angle and Setback

The thrust angle is an imaginary line drawn perpendicular to the rear axle's centerline. It compares the direction that the rear axle is aimed with the centerline of the vehicle. It also confirms if the rear axle is parallel to its front axle and that the wheelbase on both sides of the vehicle is the same. It is one of the most important diagnostic angles during an alignment.

The thrust angle is an imaginary line drawn perpendicular to the rear axle’s centerline. It compares the direction that the rear axle is aimed with the centerline of the vehicle. It also confirms if the rear axle is parallel to its front axle and that the wheelbase on both sides of the vehicle is the same. It is one of the most important diagnostic angles during an alignment.

normal thrust angleTo measure the thrust angle on a vehicle, you have to perform a four-wheel alignment. Even if the rear axle is non-adjustable, you need to take rear axle readings to properly align the front suspension.

A thrust condition exists when the rear individual toe is not equal. The thrust angle of a vehicle can be generated by two conditions or angles.  This makes it difficult for some technicians to properly diagnosis the problem. negative thrust angleFirst, the thrust angle could be generated by the angle of the axle or a misaligned rear suspension cradle that can change the toe angles. Also, a thrust angle can be generated by rear toe settings that are independent of the axle angle or implied axle angle.

The thrust angle can determine the straight-ahead position of the front wheels. So ignoring this angle can undermine even the most accurately positive thrust anglealigned front suspension. It can result in a crooked steering wheel as the front wheels steer to align themselves with the desired direction of the vehicle. Also, a misaligned thrust angle can cause the vehicle to handle differently when turning one direction versus the other.

RWD VEHICLES WITH LEAF SPRINGS

Most rear-wheel drive cars and trucks with rear leaf spring suspensions dog trackingdon’t have adjustments built into the suspension. But, the thrust line is a very important angle that can help you diagnose other problems.

If the rear live axle vehicle has a greater than normal angle, thrust angle is an indication that the axle has shifted or the mounting points on the frame have shifted.

To get a better picture of the damage, look at the setback of the front wheels. Setback is a diagnostic angle Bent Framethat measures the difference in distances between the centers of the front wheels. Differences in the setback angle can indicate damage in the frame or within components like control arms and bushings. Take a closer look at caster angles from side to side to see if there is a larger problem.

A setback and thrust angle misalignment could be an indication of frame damage. If the vehicle has suffered a recent collision that was offset, the frame may be suffering from a condition known as a “diamond frame.” This occurs when one side rail shifts in relationship to the other side rail. On a vehicle with an independent front suspension and a rear live-axle, the shifted rails will cause the front suspension to have an increased setback and thrust angle. This is caused by the mounting points of the suspension moving.

Another piece of diagnostic information to look at is the ride height. On rear suspensions with leaf springs, the leaves of the springs can become damaged and can change the ride height and the position of the axle.

One remedy for this problem is a plate that can go between the axle and springs, and allows some fore and aft repositioning of the axle to equalize rear toe readings on both sides.

Install the plate on the side of the vehicle which will help to equalize ride height. Installation of this kit may change ride height 1/2 inch. If ride height is negligible, then installation should be done on the right side for leaf springs above the axle (left side for leaf springs below the axle) to account for road crown.
Axle housings can become bent from impacts. If you see an axle with a difference in toe greater than .50º look at the axle for possible damage.

Rocking the Cradle
More and more automakers are offering all-wheel-drive on an increasing number of vehicles from small SUVs to compact sedans. On these vehicles they are mounting the differential and suspension components of a cradle that may only connect to the uni-body in four to six locations. While this may make for easy assembly, it makes the alignment technician’s job more difficult.

When aligning these types of vehicles, pay attention to rear wheel setback and the thrust angle. These diagnostic angles can help you determine if the cradle or suspension components are damaged. Most thrust angle problems on these suspensions can be resolved with toe adjustments. But, if the cradle has shifted, you may quickly run out of adjustment on the toe links.

You May Also Like

Ride Height Sensors

If one of these sensors is replaced, it must be calibrated after it is installed.

Ride-height sensors not only measure the position of the suspension, but also the rate of movement. They are supplied with a voltage of around 5 volts. The signal voltage is changed as a magnet moves past a coil. Most sensors have three wires — ground, power and signal.

Internally, it is difficult to damage one of these sensors. Externally, the linkage that connects the sensor to the suspension arm can also be damaged. The connector can be damaged and cause a short or open and a code will be set. If one of these sensors is replaced, it must be calibrated after it is installed.

GM Rattle or Creak Noise From Front Suspension

The noise may be originating from the front lower control arm front bushing. Here’s how to correct it.

Mercedes Airmatic Suspensions

Diagnostic tips to aid your repair efforts.

The Complete Shock And Strut Swap

One mistake to avoid when replacing struts is reusing the bearing plates or upper mounts.

ADAS Sensor Corrections

When performing a calibration, you are adjusting the connection between the sensor, vehicle and surroundings.

Other Posts

Collision Blueprinting with Alignment Equipment (VIDEO)

An alignment is usually called for prior to ADAS calibrations. This video is sponsored by Hunter Engineering.

Struts and Memory Steer

We can summarize the cause of memory steer in one word: binding.

Reprogramming ADAS Procedures

As a vehicle ages, the J2534 programming becomes even more important to the vehicle’s ADAS operation.

Air Ride Conversion Kits

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring.