A/C Compressors Take A Pounding

A/C Compressors Take A Pounding

The A/C compressor is a pump that compresses and circulates refrigerant within the A/C system. Some have pistons inside while others have rotating vanes on an eccentric or a pair of metal scrolls or spirals around an eccentric. Many late-model vehicles have "variable displacement" compressors that change the piston stroke to increase or decrease the volume of refrigerant flowing through the system. Some of these run continuously instead of cycling on and off like conventional A/C compressors.

If an A/C system is found to contain sludge or black gunk, it means everything in the system is contaminated and must either be cleaned or replaced.

The A/C compressor is a pump that compresses and circulates refrigerant within the A/C system. Some have pistons inside while others have rotating vanes on an eccentric or a pair of metal scrolls or spirals around an eccentric. Many late-model vehicles have “variable displacement” compressors that change the piston stroke to increase or decrease the volume of refrigerant flowing through the system. Some of these run continuously instead of cycling on and off like conventional A/C compressors.

With operating pressures up to several hundred pounds per square inch and operating temperatures of several hundred degrees, all types of compressors really take a pounding. To survive in this kind of operating environment, the compressor needs plenty of lubrication and the correct compressor oil. The system must also be free of acids, contaminants and sludge.

Over time, loss of refrigerant, loss of lubricant, lubricant breakdown, system contamination, and/or loss of cooling efficiency (plugged condenser or an inoperative cooling fan) can lead to compressor failure.

A catastrophic compressor failure is bad news because flakes of metal can be spewed out of the compressor into the inlet and outlet hoses and condenser. If the system is not thoroughly cleaned and/or the condenser replaced, the debris may clog the orifice tube causing a loss of cooling, or it may contaminate the new compressor causing it to fail.

If an A/C system is found to contain sludge or black gunk, it means everything in the system is contaminated and must either be cleaned or replaced. “Black Death” occurs when moisture enters the system, reacts with the refrigerant and oil to form acids and sludge. The resulting black gunk can clog the system or damage the compressor.

Some components such as hoses and the evaporator can be safely cleaned using an approved A/C flushing chemical. Single tube serpentine-style condensers can be flushed but not parallel flow condensers.

Additional parts that should be replaced following a compressor failure include:
● Condenser (unless the original is a serpentine style that can be flushed);
● Orifice tube; and
● Accumulator or receiver drier.

In addition, your customer will also need the type of compressor lubricant specified by the compressor manufacturer, and R134a refrigerant to recharge the A/C system.

Newer vehicles (1994 & up) that are factory-equipped with R-134a refrigerant require various types of PAG (polyalkaline glycol) oil. There are several different viscosities of PAG oil ranging from 46 to 150, so make sure your customer gets the correct type for his compressor. Using the wrong type of PAG oil can cause premature compressor wear and failure.

If an older vehicle is being retrofitted from R-12 to R-134a, POE (polyester) oil or the specified PAG oil must be used instead of mineral oil. Mineral oil should only be used in older R-12 systems (although some new compressors are shipped with a small amount of mineral oil inside to prevent a dry start).

Replacing an A/C compressor requires thoroughly evacuating the A/C system with a high vacuum pump to remove all traces of air and moisture after the compressor has been installed. If this is not done, air can displace refrigerant preventing the system from cooling normally. Air contamination will also make the compressor noisy.

The drive belt that turns the compressor should also be inspected and replaced if worn, cracked, glazed or oil-fouled.

You May Also Like

Mitchell 1, ASE Present 2022 Technician of the Future Award

Nathanial “Nate” Nie of Mission Viejo, California, was named the 2022 Mitchell 1 / National Institute for ASE Technician of the Future.

Nathanial “Nate” Nie of Mission Viejo, California, was named the 2022 Mitchell 1 / National Institute for Automotive Service Excellence (ASE) Technician of the Future during the ASE Board of Governors Meeting and Technician Awards banquet held recently in San Diego, California.

“We congratulate Nate on being named the 2022 Technician of the Future,” said Nick DiVerde, senior marketing director, Mitchell 1. “His accomplishments thus far have demonstrated his commitment to excelling as an automotive technician and we know he will continue to be successful as he journeys down his career path.”

Schaeffler Group Releases Series of LuK TSBs

In conjunction with its REPXPERT service brand, Schaeffler provides technical tips and service information for LuK products.

GB Remanufacturing Releases 2022 Year in Review

The GB Reman 2022 Year in Review is available for download.

Survey Shows Greater Trust in Service Professionals

More than 70% reported increased levels of trust in repair shops and/or service technicians.

SMP Closes the Year with 214 New Part Numbers

SMP says it is committed to providing replacement parts for hybrids and EVs through its Standard and Four Seasons brands.

Other Posts

NRS Brakes Adds 18 New Part Numbers for Multiple Models

According to NRS, these additions cover around 11.7 million vehicles.

ASE Offering Options for Testing and Recertification

ASE offers three testing options for service pros – in-person testing; the ASE renewal app; and ProProctor remote testing.

Bosch Releases Hydro-Boost Power Brake Assemblies

Hydro-Boost Power Brake Assembly now available to independent repair shops and DIY’ers.

Akebono Expands EURO Ultra-Premium Disc Brake Pad Kits

Company increases coverage by over 640,000 vehicles.