Tech Tip: Troubleshooting Common Crank Grinding Problems

Tech Tip: Troubleshooting Common Crank Grinding Problems

Using an improper wheel is most likely to blame for metal particles lodging in abrasive grains or in wheel pores. Try using a wheel with a coarser grit or more open structure to provide chip clearance. Also try using more coolant. Faulty dressing could be another cause of wheel loading. Examine your diamond tool and replace it if it appears to be worn. A worn diamond will appear rounded.

PROBLEM: Wheel loading
Using an improper wheel is most likely to blame for metal particles lodging in abrasive grains or in wheel pores. Try using a wheel with a coarser grit or more open structure to provide chip clearance. Also try using more coolant. Faulty dressing could be another cause of wheel loading. Examine your diamond tool and replace it if it appears to be worn. A worn diamond will appear rounded. During the dressing process, a rounded diamond will roll some of the severed wheel back into its pores. This causes the wheel to become loaded, even before grinding. Also, check your coolant to make sure it’s not too concentrated. And, be sure to change dirty coolant.

PROBLEM: Wheel glazing
If your wheel looks shiny and feels slick, be sure that the wheel you are using is the right one for the application. You may need to choose a wheel with a coarser grit or softer grade. Or, you can try manipulating the wheel to get a softer grinding effect. Be sure to use a sharp diamond tool to dress the wheel. Turn the diamond 1/4 turn every fifth dressing. Use faster traverse and deeper penetration. The grinding operator should try using more in-feed, this should help deter wheel glazing.

PROBLEM: Fine spiral or thread on work
This is most likely caused by a faulty wheel dresser. Replace cracked diamond or reseat diamond. Try using a slower traverse speed. Rotate diamond every fifth dressing. Be sure that set screw on diamond is tight. Dress with less in-feed and do not allow the diamond to stop while in contact with the wheel. Make sure the you move the diamond evenly across the face of the wheel and re-radius the edges of the wheel.

PROBLEM: Tapered journal
Examine your grinding machine thoroughly. Correct worn ways and alignment of tail-stock and head-stock. Tighten their spindle bearings or replace worn out bearings. Re-level the machine. Check the dressing fixture for rigidity and examine the diamond itself. Try moving the point of the diamond closer to the fixture, but do not over-extend. Diamonds must be submerged in coolant continuously during dressing to maintain constant temperature. If the diamond’s shank is allowed to expand or contract with temperature change, taper will result.

PROBLEM: Chatter marks
Long, regular-spaced chatter marks that form a checkerboard pattern woould indicate that your wheel is out of balance. Re-balance the mounted wheel using th appropriate stand provided with the grinder. Remember to run the wheel without coolant to throw-off excess water to prevent water from settling at the lower edge of the wheel during storage. The wheel might also be out of round. To remedy this, true sides to face and rebalance. Regular-spaced chatter marks are usually caused by general vibration. Check for loose motor mounting bolts (head stock or wheel head) or a loose spindle pulley. Also check the balance of the motor. General chatter marks are typically due to faulty dressing. For best results, be sure to use a sharp diamond tool, rigidly held close to the wheel.

Tech Tip courtesy of Goodson Tools.

You May Also Like

MEMA Celebrates 120th Anniversary

MEMA said the milestone “underscores the association’s enduring legacy and its pivotal role in advancing the future of mobility and the interests of vehicle suppliers.”

MEMA, The Vehicle Suppliers Association, announced its 120th anniversary, a milestone it said "underscores the association's enduring legacy and its pivotal role in advancing the future of mobility and the interests of vehicle suppliers."

MEMA was founded on March 2, 1904, in Cleveland, Ohio, to represent the burgeoning automotive parts manufacturing industry. For the last 120 years, MEMA and its members have been at the forefront of advocacy, innovation and collaboration, the association said.

UniClutch Launches Clutch System in the United States

From Australian manufacturer Clutch Industries, UniClutch is a clutch system that delivers uncompromised performance.

MEMA Aftermarket Suppliers Becomes UAF Gold Lifetime Trustee

The partnership with UAF is a commitment to the future of the automotive aftermarket, MEMA Aftermarket Suppliers said.

Castrol Turns 125, Debuts New Market Strategy

As part of the new strategy, Castrol will explore opportunities in battery thermal management, digital and service solutions and data center immersion cooling.

FCS Introduces 18 New Numbers in February

The new release includes 4 shock absorbers and 14 suspension struts.

Other Posts

Philips Releases GoPure Advanced Automotive Air Purifier

It filters out 99% of bacteria and respiratory viruses and fits in the cupholder.

AP Emissions Releases New Part Numbers for February

The 12 new SKUs cover 6 million VIO.

MANN+HUMMEL NA Aftermarket Shows Right to Repair Support

Representatives from MANN+HUMMEL’s North American aftermarket brands recently visited Capitol Hill to express their support for H.R. 906.

Federated Upgrades Car Care Center Program

The enhanced program features updated signage, marketing support, image-enhancing tools, wearables, business management assistance and other information to help with day-to-day shop operations.