Electric Power Steering

Electric Power Steering

When a technology like hydraulic power steering has been around for so long, it is difficult for technicians and even the training establishment to deal with a new system like electric power steering.

These systems abandon fluid logic for electronic logic. It is not a simple exchange of power steering fluid for magnetism. Wrapping one’s mind around these can be difficult and can require a diagnostic skill set that is not unlike those needed for anti-lock brake systems (ABS).

Advantages
An EPS system’s advantage over a hydraulic system is if the engine stalls, you will still have steering assist. This advantage can also be a disadvantage if the system should shut down while the engine is running, because it is common knowledge if the engine stalls you lose steering assist.

A driver unaware of this condition would become very concerned if an electrical or electronic failure occurred while the engine was running, as the loss of assist would not be expected.

Electronic Power Steering (EPS) will probably replace the current hydraulic power steering on most vehicles. The transition from hydraulic assist to electric motor assist will provide the driver with a more positive feel and control throughout the entire speed range of the vehicle. Also, features like automatic parking can be added to a vehicles option list.

EPS systems eliminate the need for a pump, hoses and a drive belt connected to the engine using variable amounts of power. The configuration of an EPS system can allow the entire power assist system to be packaged on the rack and pinion steering gear or in the steering column.

The system does not provide assist until required by driver input. This means that there is not any drag on the engine by either a power steering pump or alternator until it is really needed. Also, there is no hydraulic fluid, which is one less use for a petroleum product.

Brushes not Flushes
A typical EPS steering application uses a bidirectional brushless motor, sensors and electronic controller to provide steering assist. The motor will drive a gear that can be connected to the steering column shaft or the steering rack. Sensors located in the steering column measure two primary driver inputs — torque (steering effort) and steering wheel speed and position.

The steering wheel is referred to as a handwheel in service information. The torque, speed and position inputs, along with the vehicle speed signal and other inputs, are interpreted into an electronic control module.

The controller processes the steering effort and handwheel position through a series of programs called algorithms for assist and return to produce the proper amount of polarity and current to the motor.

Other inputs that will affect assist and return are vehicle speeds, engine speed and chassis control systems such as ABS and Electronic Stability Control (ESC).

The brushless bidirectional permanent magnet motor and gear perform the same function as the power cylinder in a hydraulic system.

The brushless motor uses a permanent magnet rotor and three electromagnetic coils to propel the rotor. Most applications use a motor worm gear to drive the gear on the steering shaft or rack (Figure 1).

Pairs of six switching transistors are forward biased move the rotor in a clockwise or counterclockwise direction. The pairs are A+ and C-; B+ and A-; C+ and B- (Figure 2). The rotor direction is determined by the sequence in which voltage is applied to coil A, B or C and returned to ground through an attached pair. The sequence for clockwise is ABC and for counterclockwise is CBA (Figure 3).

The primary purpose of the EPS controller is to provide motor control. The processor is heart of the controller for input and output. Processor output drives the three pairs of transistors that control the rotation of the motor. Primary input to the processor comes from the torque sensor and handwheel speed and position sensor.

Other processor inputs include rotor position, motor voltage and temperature.

The processor also is an integral part of the Controlled Area Network (CAN) and vehicle data buss for chassis and powertrain communications. This data buss supplies vehicle speed, engine speed, ABS and ESC information (Figure 3). The controller has adaptive memory and diagnostics.

On-board diagnostics (OBD II) has established generic failure codes. A failure of the torque sensor would most likely set a diagnostic trouble code (DTC): U0130 — Lost Communication With Steering Effort Control Module; and U0131 — Lost Communication with Power Steering Control Module.

The DTCs C0460 and C0545 Lack of Power Assist; and C0472 and C0473 Steering Handwheel Speed Sensor Signal V Low and High will also apply. Other DTCs will be specific to the manufacturer of a particular steering gear. If the vehicle has a Driver Information Center, it can supply information about a system by displaying the message “POWER STEERING” and turning on the “service soon” light.

The torque sensor performs the same function as the torsion bar and spool valve in a hydraulic system. The electronic sensor uses a torsion bar in the same manner as in the spool valve.

There are three different types of electronic torque sensors and they are classified as contact and non-contact types. A non-contact sensor uses a magnetic rotor with alternating pole pieces and is attached to the torsion bar.

Hall-type sensors monitor the twist of the torsion bar by measuring the change in magnetic flux generated by its position to the vanes located on the sensor stator rings.

When the rotor moves, a change in magnetic flux will produce a signal to an Analog Sensing Integrated Circuit (ASIC) that will process the signal and send the information to the controller’s assist algorithm. ASIC is a description of what is generically called a “Chip” (Figure 4).

Contact type torque sensors uses a wiper attached to the torsion bar and voltage divider attached to the rotating bridge attached to the motor shaft to measure the twist of the torsion bar. The rotating bridge uses contact brushes that connect to the sensor housing and connector to receive power, ground and transfer the voltage signal to the controller (Figure 5).

The electric steering system will retain the Handwheel Speed Sensor (HWSS) for both speed and position. It will retain the four voltage divider circuits and a wiper.

The voltage dividers are constructed of a resistive material on a film powered by a five-volt reference to make four 90-degree sensing elements. The wiper has a contact that rides on the resistive film and supplies the output signal to the controller.

The signal ranges from 0.5 to 4.5 volts with a plus or minus 0.3 volts. For example: The sensor produces 0.2 to 4.8 volts when the steering wheel is rotated 90 degrees. Then the sensor produces 4.8 to 0.2 volts for the next 90 degrees of steering wheel rotation in the same direction.

When the steering wheel has been rotated 360 degrees, the voltage will have gone 0.2 to 4.8, 4.8 to 0.2, and 0.2 to 4.8, and 4.8 to 0.2 volts in a constant rising and falling voltage. New technology will continue to be introduced to existing systems. Throttle by wire is now a common feature on both domestic and import vehicles.

The Future
What’s next? Steer by wire could be the next step, which will have the same impact that EPS is having now. It could present a new concept to vehicle control. Ten years from now, the steering wheel could be replaced with something like a video game controller.

Reman Magnasteer Components
With more than 10 years on the road, many Magnasteer racks will need some attention. Theses high-tech racks are still racks that can wear out pinions, bearings and seals.

Finding replacement parts is getting easier and less expensive and many remanufacturers have added these applications to their catalogs.

Why used reman components in these application? Most large remanufacturers have experience on both the hydraulic and electrical sides. Also, the units offer, in some cases, a better value than a new rack.

On GM Magnasteer applications, the whole rack must be replaced if the rack or control unit is defective because the Magnasteer unit is part of the rack. Handle with care because the permanent magnets inside the Magnasteer valve assembly and connector are fragile and can be easily damaged.

On 1996 and 1997 applications, Magnasteer has its own separate control module. But on 1998 and newer applications, the Electronic Brake Control Module (EBCM), which also oversees the operation of the anti-lock brake system, handles the Magnasteer control function.

In 1998, a second generation “Magnasteer MAGe” system was introduced on some GM vehicles. This version of the system does not use a permanent magnet, but uses a redesigned electromagnet that has one pole mounted on the input shaft and the other on the pinion shaft.

You May Also Like

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

An alignment angle doesn’t change randomly. There is a cause-and-effect relationship between external and internal forces that can alter the geometry of a vehicle’s suspension. Having the alignment reading for only one angle on one corner is just like knowing the temperature without knowing if there is a tornado outside.

Suspension Upgrades – Selling Shocks and Struts

The question customers fail to ask is, what is “best” for their vehicle?

Air Ride Suspension Diagnostics

The key to understanding the logic of air ride systems is using service information.

Steering Angle Sensor Operations

It is important for the ABS/ESC module to receive two signals to verify the steering wheel’s position.

Chassis Alignment

The source of the complaint can be the angles, electronics or tires.

Other Posts

Laying Out Your Shop for ADAS/EV Repairs

With so many vehicles equipped with some form of ADAS, rethinking your electronics layout or plan might be in order.

Broken Springs

What is the cause for the failure? Why does it occur with specific vehicles?

The Importance Of ADAS Calibrations

Following best practices and using appropriate equipment ensure customer satisfaction and safety.

Why Do Vehicles Go Out Of Alignment

If camber, caster or toe are out of specifications, there is usually a reason why.