Honda Civic Alignment Spec: 2006-'11

Honda Civic Alignment Spec: 2006-’11

Before performing an alignment, it is critical to ­perform a thorough inspection. First, make sure the ­suspension is not modified. Many Honda owners lower their Civics with inexpensive lowering kits and springs. Second, check the tire size and set the correct tire pressure. Use the information printed on the driver's side door pillar.

Honda Civic Alignment 2Built on a high-rigidity unit-body platform, the 2006-2011 Civic has a MacPherson strut front ­suspension and a multi-link rear suspension. The eighth generation switched from a high mounted to a low mounted steering rack and significantly increased caster.

In the alignment bay, the eighth-generation Civic doesn’t hold any surprises, but it does require a sharp eye to spot potential problems.

Pre-Alignment Checks

Before performing an alignment, it is critical to ­perform a thorough inspection. First, make sure the ­suspension is not modified. Many Honda owners lower their Civics with inexpensive lowering kits and springs. Second, check the tire size and set the correct tire ­pressure. Use the information printed on the driver’s side door pillar.

Check the suspension ball joints. (Hold a wheel with your hands and move it up and down and right and left to check for wobbling.) Honda has no wear specifications for the joint, except that it cannot have any visible movement when pressure is put on the tire at 12 and 6 o’clock.

Bounce the vehicle up and down several times to settle the suspension. Listen for any rattles, clunks or pops. On some 2006 models and higher mileage vehicles, the front and rear bump stops can separate from the upper part of the struts’ mounts and slide down the rod into the dust boot. The dust boots are made of hard plastic, and as the strut compresses, it can cause a popping or crunching noise.

Honda Civic Alignment 1Front Suspension

The caster on the Civic is non-adjustable. If the measurement is not within specifications, check for bent or damaged suspension components.

The front camber can be adjusted by installing an adjustable bolt in the lower hole of the strut. The aftermarket cam bolt kits will allow for ±1.75º of adjustment. Honda does sell non-cam bolt kits that have different diameter bolts that can be used in either the lower hole or in both holes. The torque for the bolts is 67 ft.-lbs.

There are no special procedures for the front toe adjustment. Just make sure the bellows for the rack are not twisted and the bushings for the rack are in good condition. If the bushings, or even the bolts are loose, the driver my complain of a popping or clunking noise at low speeds. If the toe is adjusted, there are no documented steering position sensor reset procedures.

Honda Civic Alignment 3Rear Suspension

The rear suspension on the eighth-generation Civic uses a lower control arm and an upper link. The toe is adjustable but requires extra parts to adjust the camber.

To adjust the rear toe, hold the adjusting bolt on the trailing arm and remove the self-locking nut. Always use a new self-locking nut whenever it has been loosened. Reassemble the adjusting bolt and complete with the eccentric facing up. Adjust the rear toe by turning the adjusting bolt until the toe is correct and tighten the new self-locking nut while holding the adjusting bolt.

The rear camber is not factory adjustable. Adjusting the camber on 2006 to 2011 Civics requires an aftermarket kit that replaces the bracket on the body for the upper link with an eccentric cam bolt. The kit will give ±1.25° of rear camber change. It requires a half hour of labor per side to install the kit.

The Mystery of the Letter “C” Rear Control Arms

For some 2006-’07 Civics, Honda issued a TSB about updated replacement rear control arms stamped with the letter “C”.
Honda was receiving complaints about uneven and rapid rear tire wear. Also, customers complained of a roaring noise from the rear, or a vibration at highway speeds.

Honda claimed the combination of the stock tires, rear suspension geometry and alignment angles caused rapid and uneven rear tire wear. Honda recommends the installation of new control rear arms stamped with the letter “C”. The new control arms take out 0.75º of camber from the rear. The same reduction in camber can be achieved with a bracket kit with a replacement eccentric cam bolt. This may be more economical than installing the control arms from Honda and will allow for adjustments due to damage or vehicle aging. After the installation, align to the “C” specs.

Vehicles
•2006-’07 2-Door (Except Si and Honda Accessory HFP Package)
•2006-’07 4-Door – Except Si
•2006-’07 Hybrid – ALL
•2008 Hybrid (VIN JHMFA3…8S000001 thru JHMFA3…8S010456).

You May Also Like

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

An alignment angle doesn’t change randomly. There is a cause-and-effect relationship between external and internal forces that can alter the geometry of a vehicle’s suspension. Having the alignment reading for only one angle on one corner is just like knowing the temperature without knowing if there is a tornado outside.

Suspension Upgrades – Selling Shocks and Struts

The question customers fail to ask is, what is “best” for their vehicle?

Air Ride Suspension Diagnostics

The key to understanding the logic of air ride systems is using service information.

Steering Angle Sensor Operations

It is important for the ABS/ESC module to receive two signals to verify the steering wheel’s position.

Chassis Alignment

The source of the complaint can be the angles, electronics or tires.

Other Posts

Audi MLB Alignment

The alignment of these vehicles can be straightforward mechanically

Solid Axle Bearing Restoration

A solid axle might seem like antiquated technology. However, many vehicles still utilize solid or live axles because of their load-carrying capabilities. An axle is not a sealed unit. Inside are bearings, seals and fluids that must be serviced. Also, replacement parts are available from BCA. It’s not uncommon for a solid rear axle vehicle

AWD and ABS Services

AWD is always engaged and with the ABS brake modulator, can perform like systems with limited-slip differentials.

Laying Out Your Shop for ADAS/EV Repairs

With so many vehicles equipped with some form of ADAS, rethinking your electronics layout or plan might be in order.